GMCforum: GMCnet » [GMCnet] bearings

Home » Public Forums » GMCnet » [GMCnet] bearings

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] bearings [message #328027 is a reply to message #328024]

Mon, 08 January 2018 12:11

emerystora

Messages: 4442
Registered: January 2004

Karma:

Senior Member

Yes the zerk fitting hole can be drilled in place but the axle and bearing has to be out. Jim Kanomata has a jig available that works great. You just need a 6” long 1/8” drill bit. You also have to cut grooves in the bearing spacer with a Dremel tool.
Then tap threads into the outside hole and thread in a grease fitting.

The only problem with this is that you must first determine whether there us wear on the hub or inside if the knuckle.
You can do this with calipers but an expert like Dave Lenzi and others will do it properly which is why the recommendation to ship them off for rebuilding.

Emery Stora
77 Kingsley
Frederick, CO

> On Jan 8, 2018, at 10:13 AM, Brian Waddell wrote:
>
>
> reasonable suggestion...thanks...been told before....Brian
>
> ________________________________
> From: Gmclist on behalf of jhb1
> Sent: January 8, 2018 6:42 AM
> To: gmclist@list.gmcnet.org
> Subject: Re: [GMCnet] bearings
>
> Jack the coach up and pull the knuckles put them in a crate drive to the coming west ups place in the UPSand
> ship them to JimB or JImK and it will probably cost you less than driving to the class West I lace
>
> HTH
> --
> John H. Bell
> 77 Royale; QuadBag,Manny OneTon,Honda EV4010, FITech
> Montreal Qc.
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
> Gmclist Info Page - GMCnet
> list.gmcnet.org
> To see the collection of prior postings to the list, visit the Gmclist Archives. Using Gmclist: To post a message to all the list members, send email ...
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

[Message index]

		[GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 16:07
		Re: [GMCnet] bearings By: JohnL455 on Sun, 07 January 2018 17:03
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:28
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 16:59
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:23
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 17:27
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:42
		Re: [GMCnet] bearings By: Larry on Sun, 07 January 2018 17:44
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 17:45
		Re: [GMCnet] bearings By: bdub on Sun, 07 January 2018 18:11
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 18:27
		Re: [GMCnet] bearings By: USAussie on Sun, 07 January 2018 18:36
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 18:42
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 19:05
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:49
		Re: [GMCnet] bearings By: bdub on Sun, 07 January 2018 19:02
		Re: [GMCnet] bearings By: Mike Kelley on Sun, 07 January 2018 19:06
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 20:25
		Re: [GMCnet] bearings By: Rollerg on Mon, 08 January 2018 18:45
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 19:49
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:44
		Re: [GMCnet] bearings By: USAussie on Sun, 07 January 2018 18:15
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:57
		Re: [GMCnet] bearings By: lqqkatjon on Sun, 07 January 2018 20:40
		Re: [GMCnet] bearings By: Ken Burton on Sun, 07 January 2018 22:16
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 23:50
		Re: [GMCnet] bearings By: USAussie on Mon, 08 January 2018 00:40
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:00
		Re: [GMCnet] bearings By: jhb1 on Mon, 08 January 2018 07:42
		Re: [GMCnet] bearings By: Bullitthead on Mon, 08 January 2018 08:40
		Re: [GMCnet] bearings By: Ken Burton on Mon, 08 January 2018 09:02
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:13
		Re: [GMCnet] bearings By: emerystora on Mon, 08 January 2018 12:11
		Re: [GMCnet] bearings By: Ken Burton on Mon, 08 January 2018 18:49
		Re: [GMCnet] bearings By: BobDunahugh on Mon, 08 January 2018 11:05
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:34
		Re: [GMCnet] bearings By: Richard Denney on Mon, 08 January 2018 21:46
		Re: [GMCnet] bearings By: hal kading on Mon, 08 January 2018 23:35

Previous Topic:	[GMCnet] How I stop ME from not completeing task on our GMC.
Next Topic:	Classic Ride // Classic Cult

Goto Forum:

-=] Back to Top [=-

Current Time: Sat May 11 09:06:00 CDT 2024

Total time taken to generate the page: 0.00720 seconds