GMCforum: GMCnet » [GMCnet] bearings

Home » Public Forums » GMCnet » [GMCnet] bearings

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] bearings [message #328016 is a reply to message #328009]

Mon, 08 January 2018 09:02

Ken Burton

Messages: 10030
Registered: January 2004
Location: Hebron, Indiana

Karma:

Senior Member

You are right. I was thinking about removing the lower control arms or torsion bar. It is Not necessary on knuckle. It has been a long time since I did one. Front coach weight does need to be supported on the lower control arm. Do not let the lower control arm just hang down. I usually jack it up in the center and then put some jack stands or 4x4 cribbing under each control arm. Then drop the coach on them. I leave the lowered jack in the middle with a light amount of weight on it just for some extra safety.

Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana

Report message to a moderator

[Message index]

		[GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 16:07
		Re: [GMCnet] bearings By: JohnL455 on Sun, 07 January 2018 17:03
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:28
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 16:59
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:23
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 17:27
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:42
		Re: [GMCnet] bearings By: Larry on Sun, 07 January 2018 17:44
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 17:45
		Re: [GMCnet] bearings By: bdub on Sun, 07 January 2018 18:11
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 18:27
		Re: [GMCnet] bearings By: USAussie on Sun, 07 January 2018 18:36
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 18:42
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 19:05
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:49
		Re: [GMCnet] bearings By: bdub on Sun, 07 January 2018 19:02
		Re: [GMCnet] bearings By: Mike Kelley on Sun, 07 January 2018 19:06
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 20:25
		Re: [GMCnet] bearings By: Rollerg on Mon, 08 January 2018 18:45
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 19:49
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:44
		Re: [GMCnet] bearings By: USAussie on Sun, 07 January 2018 18:15
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:57
		Re: [GMCnet] bearings By: lqqkatjon on Sun, 07 January 2018 20:40
		Re: [GMCnet] bearings By: Ken Burton on Sun, 07 January 2018 22:16
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 23:50
		Re: [GMCnet] bearings By: USAussie on Mon, 08 January 2018 00:40
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:00
		Re: [GMCnet] bearings By: jhb1 on Mon, 08 January 2018 07:42
		Re: [GMCnet] bearings By: Bullitthead on Mon, 08 January 2018 08:40
		Re: [GMCnet] bearings By: Ken Burton on Mon, 08 January 2018 09:02
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:13
		Re: [GMCnet] bearings By: emerystora on Mon, 08 January 2018 12:11
		Re: [GMCnet] bearings By: Ken Burton on Mon, 08 January 2018 18:49
		Re: [GMCnet] bearings By: BobDunahugh on Mon, 08 January 2018 11:05
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:34
		Re: [GMCnet] bearings By: Richard Denney on Mon, 08 January 2018 21:46
		Re: [GMCnet] bearings By: hal kading on Mon, 08 January 2018 23:35

Previous Topic:	[GMCnet] How I stop ME from not completeing task on our GMC.
Next Topic:	Classic Ride // Classic Cult

Goto Forum:

-=] Back to Top [=-

Current Time: Sat May 11 14:26:40 CDT 2024

Total time taken to generate the page: 0.01243 seconds