Home » Public Forums » GMCnet » [GMCnet] bearings
| Re: [GMCnet] bearings [message #327968 is a reply to message #327966] |
Sun, 07 January 2018 17:42   |
Brian Waddell
Messages: 409
Registered: March 2010
Karma:
|
Senior Member |
|
|
been through this but thanks for the suggestions...new BFG radial 16 inch with new alcoas varied psi...no change...new hub extensions on and off...no change....new relay and pitmann and alignment and other pivot point arm (forget name)...no change and steering linkage and steering cv new lube and tolerences checked and taken off and tried and tried different positions on that blue telescoping shaft and everything is tight and no change...steering box maybe next but would like to do the front wheell bearings anyway..... by driving it somewhere......where???..Brian 77 ele 455
________________________________
From: Gmclist on behalf of James Hupy
Sent: January 7, 2018 4:27 PM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] bearings
How about tires? Are you running all steel belts, or steel belt treads with
rag sidewalls? Inflation pressures?
Jim Hupy
On Jan 7, 2018 3:24 PM, "Brian Waddell" wrote:
replaced the rear bearings and did all measurements on the bogies ....solid
tight and nothing bent...Brian 77 ele 455
________________________________
From: Gmclist on behalf of James Hupy <
jamesh1296@gmail.com>
Sent: January 7, 2018 3:59 PM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] bearings
Brian, remember this point. "When you can't figure out why you coach won't
steer, look to the rear end. The back end CAN and DOES steer the coach."
Particularly the forward bogies.
Jim Hupy
Salem, Or
78 GMC ROYALE 403
On Jan 7, 2018 2:08 PM, "Brian Waddell" wrote:
> I have not used my 77 gmc elegansa mostly because the steering is so
> bad...I have replaced most components ordered from Dave L.....might
replace
> the steering box next...I have discussed steering issues with the gmcnet
in
> the past. I have new front bearings and seals from Jim K. I bought them
a
> few years ago but decided not to install them as I know I am not
> qualified...So my question...Me and the gmc are situated near Winnipeg
> Manitoba Canada...grand forks Noth Dakota 125mi. or so south...Where is
the
> closest place I could drive this coach to have someone qualified do front
> wheel bearings etc with grease fittings?..
>
> brian 77 ele 455
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Gmclist Info Page - GMCnet
list.gmcnet.org
To see the collection of prior postings to the list, visit the Gmclist Archives. Using Gmclist: To post a message to all the list members, send email ...
Gmclist Info Page - GMCnet
list.gmcnet.org
To see the collection of prior postings to the list, visit the Gmclist
Archives. Using Gmclist: To post a message to all the list members, send
email ...
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Gmclist Info Page - GMCnet
list.gmcnet.org
To see the collection of prior postings to the list, visit the Gmclist
Archives. Using Gmclist: To post a message to all the list members, send
email ...
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
 |
|
[GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
By: JohnL455 on Sun, 07 January 2018 17:03 |
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
By: Larry on Sun, 07 January 2018 17:44 |
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
By: bdub on Sun, 07 January 2018 18:11 |
|
|
Re: [GMCnet] bearings
By: jimk on Sun, 07 January 2018 18:27 |
|
|
Re: [GMCnet] bearings
By: USAussie on Sun, 07 January 2018 18:36 |
|
|
Re: [GMCnet] bearings
By: jimk on Sun, 07 January 2018 18:42 |
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
By: bdub on Sun, 07 January 2018 19:02 |
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
By: Rollerg on Mon, 08 January 2018 18:45 |
|
|
Re: [GMCnet] bearings
By: jimk on Sun, 07 January 2018 19:49 |
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
By: USAussie on Sun, 07 January 2018 18:15 |
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
By: USAussie on Mon, 08 January 2018 00:40 |
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
By: jhb1 on Mon, 08 January 2018 07:42 |
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
|
|
Re: [GMCnet] bearings
|
Goto Forum:
Current Time: Sat May 11 12:21:26 CDT 2024
Total time taken to generate the page: 0.00795 seconds
|
GMCforum
Search
Help
Register
Login
Home
