GMCforum: GMCnet » [GMCnet] bearings

Home » Public Forums » GMCnet » [GMCnet] bearings

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] bearings [message #327963 is a reply to message #327960]

Sun, 07 January 2018 16:59

James Hupy

Messages: 6806
Registered: May 2010

Karma:

Senior Member

Brian, remember this point. "When you can't figure out why you coach won't
steer, look to the rear end. The back end CAN and DOES steer the coach."
Particularly the forward bogies.
Jim Hupy
Salem, Or
78 GMC ROYALE 403

On Jan 7, 2018 2:08 PM, "Brian Waddell" wrote:

> I have not used my 77 gmc elegansa mostly because the steering is so
> bad...I have replaced most components ordered from Dave L.....might replace
> the steering box next...I have discussed steering issues with the gmcnet in
> the past. I have new front bearings and seals from Jim K. I bought them a
> few years ago but decided not to install them as I know I am not
> qualified...So my question...Me and the gmc are situated near Winnipeg
> Manitoba Canada...grand forks Noth Dakota 125mi. or so south...Where is the
> closest place I could drive this coach to have someone qualified do front
> wheel bearings etc with grease fittings?..
>
> brian 77 ele 455
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

[Message index]

		[GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 16:07
		Re: [GMCnet] bearings By: JohnL455 on Sun, 07 January 2018 17:03
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:28
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 16:59
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:23
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 17:27
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 17:42
		Re: [GMCnet] bearings By: Larry on Sun, 07 January 2018 17:44
		Re: [GMCnet] bearings By: James Hupy on Sun, 07 January 2018 17:45
		Re: [GMCnet] bearings By: bdub on Sun, 07 January 2018 18:11
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 18:27
		Re: [GMCnet] bearings By: USAussie on Sun, 07 January 2018 18:36
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 18:42
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 19:05
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:49
		Re: [GMCnet] bearings By: bdub on Sun, 07 January 2018 19:02
		Re: [GMCnet] bearings By: Mike Kelley on Sun, 07 January 2018 19:06
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 20:25
		Re: [GMCnet] bearings By: Rollerg on Mon, 08 January 2018 18:45
		Re: [GMCnet] bearings By: jimk on Sun, 07 January 2018 19:49
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:44
		Re: [GMCnet] bearings By: USAussie on Sun, 07 January 2018 18:15
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 18:57
		Re: [GMCnet] bearings By: lqqkatjon on Sun, 07 January 2018 20:40
		Re: [GMCnet] bearings By: Ken Burton on Sun, 07 January 2018 22:16
		Re: [GMCnet] bearings By: Brian Waddell on Sun, 07 January 2018 23:50
		Re: [GMCnet] bearings By: USAussie on Mon, 08 January 2018 00:40
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:00
		Re: [GMCnet] bearings By: jhb1 on Mon, 08 January 2018 07:42
		Re: [GMCnet] bearings By: Bullitthead on Mon, 08 January 2018 08:40
		Re: [GMCnet] bearings By: Ken Burton on Mon, 08 January 2018 09:02
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:13
		Re: [GMCnet] bearings By: emerystora on Mon, 08 January 2018 12:11
		Re: [GMCnet] bearings By: Ken Burton on Mon, 08 January 2018 18:49
		Re: [GMCnet] bearings By: BobDunahugh on Mon, 08 January 2018 11:05
		Re: [GMCnet] bearings By: Brian Waddell on Mon, 08 January 2018 11:34
		Re: [GMCnet] bearings By: Richard Denney on Mon, 08 January 2018 21:46
		Re: [GMCnet] bearings By: hal kading on Mon, 08 January 2018 23:35

Previous Topic:	[GMCnet] How I stop ME from not completeing task on our GMC.
Next Topic:	Classic Ride // Classic Cult

Goto Forum:

-=] Back to Top [=-

Current Time: Sat May 11 08:46:49 CDT 2024

Total time taken to generate the page: 0.01190 seconds