GMCforum: GMCnet » starting the engine

Home » Public Forums » GMCnet » starting the engine

Show: Today's Messages :: Polls :: Message Navigator

Re: starting the engine [message #322140 is a reply to message #321702]

Tue, 15 August 2017 11:05

jhbridges

Messages: 8412
Registered: May 2011
Location: Braselton ga

Karma:

Senior Member

Pressing the throttle on a cold non-running engine should result in the front (choke) plate closing. If it does not, investigate whay. With the three screws loose on the black round spring cover on the passenger side of the carb, rotating the black part with the throttle pressed and engine off should move the choke plate in either direction. If it dies, turn it until the plate >just< closes and tighten the three screws. This will be close to the correct setting. UIf the choke doesn't close, or binds, stop and figure put why and correct. Then set it again and try cranking the engine.
This assumes a stock setup with a 'stove pipe' running ffrom the stove on the manifold to the choke spring assembly. If you have a wire instead of a heat tube, the setup will be a bit different.

--johnny

--johnny

Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons. Braselton, Ga. I forgive them all, save those who hurt the dogs. They must answer to me in hell

Report message to a moderator

[Message index]

		starting the engine By: kstockwell on Sun, 06 August 2017 13:55
		Re: starting the engine By: shaunone on Sun, 06 August 2017 14:18
		Re: starting the engine By: kstockwell on Sun, 06 August 2017 14:26
		Re: starting the engine By: Carl S. on Sun, 06 August 2017 14:49
		Re: [GMCnet] starting the engine By: James Hupy on Sun, 06 August 2017 14:51
		Re: [GMCnet] starting the engine By: kstockwell on Sun, 06 August 2017 20:16
		Re: [GMCnet] starting the engine By: k2gkk on Sun, 06 August 2017 20:25
		Re: [GMCnet] starting the engine By: kstockwell on Sun, 06 August 2017 20:38
		Re: [GMCnet] starting the engine By: k2gkk on Sun, 06 August 2017 22:24
		Re: [GMCnet] starting the engine By: Richard Denney on Sun, 06 August 2017 22:57
		Re: starting the engine By: mrgmc3 on Sun, 06 August 2017 23:15
		Re: [GMCnet] starting the engine By: ljdavick on Mon, 07 August 2017 01:14
		Re: starting the engine By: Chris Tyler on Mon, 07 August 2017 04:24
		Re: [GMCnet] starting the engine By: Bruce Hart on Mon, 07 August 2017 06:13
		Re: [GMCnet] starting the engine By: kstockwell on Mon, 07 August 2017 07:15
		Re: starting the engine By: JohnL455 on Mon, 07 August 2017 08:56
		Re: starting the engine By: kstockwell on Sun, 13 August 2017 14:11
		Re: starting the engine By: kstockwell on Sun, 13 August 2017 14:35
		Re: [GMCnet] starting the engine By: Keith V on Mon, 14 August 2017 09:00
		Re: [GMCnet] starting the engine By: kstockwell on Mon, 14 August 2017 14:45
		Re: [GMCnet] starting the engine By: Keith V on Mon, 14 August 2017 15:20
		Re: [GMCnet] starting the engine By: kstockwell on Mon, 14 August 2017 18:00
		Re: [GMCnet] starting the engine By: 77Royale on Mon, 14 August 2017 15:34
		Re: [GMCnet] starting the engine By: kstockwell on Mon, 14 August 2017 18:25
		Re: [GMCnet] starting the engine By: k2gkk on Mon, 14 August 2017 16:21
		Re: [GMCnet] starting the engine By: kstockwell on Mon, 14 August 2017 18:02
		Re: [GMCnet] starting the engine By: k2gkk on Mon, 14 August 2017 20:35
		Re: [GMCnet] starting the engine By: Keith V on Tue, 15 August 2017 08:43
		Re: starting the engine By: JohnL455 on Tue, 15 August 2017 08:44
		Re: [GMCnet] starting the engine By: bdub on Tue, 15 August 2017 09:23
		Re: [GMCnet] starting the engine By: kstockwell on Wed, 16 August 2017 06:14
		Re: [GMCnet] starting the engine By: kstockwell on Wed, 16 August 2017 06:18
		Re: [GMCnet] starting the engine By: Richard Denney on Wed, 16 August 2017 07:03
		Re: [GMCnet] starting the engine By: USAussie on Wed, 16 August 2017 07:19
		Re: [GMCnet] starting the engine By: kstockwell on Wed, 16 August 2017 08:16
		Re: starting the engine By: jhbridges on Tue, 15 August 2017 11:05
		Re: starting the engine By: 77Royale on Wed, 16 August 2017 07:27
		Re: starting the engine By: kstockwell on Wed, 16 August 2017 19:17
		Re: starting the engine By: jhbridges on Thu, 17 August 2017 08:15
		Re: starting the engine By: kstockwell on Thu, 17 August 2017 10:11
		Re: [GMCnet] starting the engine By: James Hupy on Thu, 17 August 2017 10:26
		Re: [GMCnet] starting the engine By: jimk on Thu, 17 August 2017 11:02
		Re: [GMCnet] starting the engine By: kstockwell on Thu, 17 August 2017 11:29
		Re: [GMCnet] starting the engine By: kstockwell on Thu, 17 August 2017 17:35
		Re: [GMCnet] starting the engine By: James Hupy on Thu, 17 August 2017 18:00
		Re: [GMCnet] starting the engine By: kstockwell on Thu, 17 August 2017 18:19
		Re: [GMCnet] starting the engine By: James Hupy on Thu, 17 August 2017 18:25
		Re: [GMCnet] starting the engine By: kstockwell on Thu, 17 August 2017 18:35
		Re: [GMCnet] starting the engine By: kstockwell on Thu, 17 August 2017 18:34
		Re: [GMCnet] starting the engine By: kstockwell on Sun, 20 August 2017 08:05
		Re: [GMCnet] starting the engine By: James Hupy on Sun, 20 August 2017 09:00
		Re: [GMCnet] starting the engine By: kstockwell on Sun, 20 August 2017 09:29
		Re: starting the engine By: kstockwell on Sat, 19 August 2017 15:16
		Re: starting the engine By: C Boyd on Sat, 19 August 2017 19:00
		Re: starting the engine By: kstockwell on Sun, 20 August 2017 07:42

Previous Topic:	[GMCnet] Oil sputtering (4K) Onan
Next Topic:	Re: [GMCnet] Whitch speedometer fits in 1975 GMC Motor home

Goto Forum:

-=] Back to Top [=-

Current Time: Sun May 19 21:57:53 CDT 2024

Total time taken to generate the page: 0.29877 seconds