GMCforum: GMCnet » ONAN starting

Home » Public Forums » GMCnet » ONAN starting (starter stays engaged after starting)

Show: Today's Messages :: Polls :: Message Navigator

ONAN starting [message #320793]

Fri, 21 July 2017 14:04

Bill Shourt

Messages: 33
Registered: January 2005
Location: Sherman Oaks ,Ca

Karma:

Member

Onan starter stays engaged after engine starts occasionally, usually when cold. When I pull the connector off the start solenoid it disengages immediatly. Voltage to starter is 12 volts when starting and drops to 8 volts when running. When I pull the wire off starter it drops to 0. If i put wire back on 0 volts and no starter running.
33 volts across 5 and 8 when running
New dino board, it did this occasionaly with the old board also, but rarely.
New K1 relay
metered across 12 pin connector, 0 or .1 ohms on all connectors.
battery charger out of circuit.
Any ideas for more things to check?

Bill and Michele Shourt
78 Kingsley, origional

Report message to a moderator

[Message index]

		ONAN starting By: Bill Shourt on Fri, 21 July 2017 14:04
		Re: [GMCnet] ONAN starting By: James Hupy on Fri, 21 July 2017 14:49
		Re: [GMCnet] ONAN starting By: William Shourt on Fri, 21 July 2017 18:15
		Re: [GMCnet] ONAN starting By: Carl S. on Fri, 21 July 2017 19:09
		Re: [GMCnet] ONAN starting By: William Shourt on Fri, 21 July 2017 19:17
		Re: ONAN starting By: lqqkatjon on Fri, 21 July 2017 22:35
		Re: ONAN starting By: Ken Burton on Sat, 22 July 2017 04:11
		Re: [GMCnet] ONAN starting By: Mr ERFisher on Sat, 22 July 2017 04:49
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 07:51
		Re: [GMCnet] ONAN starting By: Ken Burton on Sat, 22 July 2017 10:54
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 13:29
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 14:07
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 14:48
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 13:46
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sat, 22 July 2017 18:00
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 19:09
		Re: [GMCnet] ONAN starting By: bwevers on Sat, 22 July 2017 20:32
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sat, 22 July 2017 22:51
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sun, 23 July 2017 09:53
		Re: [GMCnet] ONAN starting By: William Shourt on Sun, 23 July 2017 18:17
		Re: [GMCnet] ONAN starting By: Guy Lopes on Tue, 25 July 2017 00:51
		Re: [GMCnet] ONAN starting By: Bruce Hart on Tue, 25 July 2017 05:59
		Re: [GMCnet] ONAN starting By: Ken Henderson on Tue, 25 July 2017 06:09
		Re: [GMCnet] ONAN starting By: jimk on Tue, 25 July 2017 10:03
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:23
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:29
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:32
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 14:19
		Re: [GMCnet] ONAN starting By: Ken Burton on Tue, 25 July 2017 15:11
		Re: [GMCnet] ONAN starting By: Emery Stora on Tue, 25 July 2017 20:30
		Re: [GMCnet] ONAN starting By: Ken Henderson on Tue, 25 July 2017 21:15
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 07:57
		Re: ONAN starting By: lqqkatjon on Sat, 22 July 2017 15:32
		Re: ONAN starting By: Ken Burton on Sat, 22 July 2017 20:14
		Re: ONAN starting By: JohnL455 on Sun, 23 July 2017 16:34
		Re: ONAN starting By: JohnL455 on Sun, 23 July 2017 16:38
		Re: ONAN starting By: Ken Burton on Sun, 23 July 2017 21:17
		Re: [GMCnet] ONAN starting By: William Shourt on Sun, 23 July 2017 23:09
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sun, 23 July 2017 23:35
		Re: ONAN starting about 2 K windings By: Matt Colie on Mon, 24 July 2017 09:28
		Re: [GMCnet] ONAN starting about 2 K windings By: William Shourt on Mon, 24 July 2017 13:26
		Re: [GMCnet] ONAN starting about 2 K windings By: Ken Henderson on Mon, 24 July 2017 20:56
		Re: [GMCnet] ONAN starting about 2 K windings By: Bullitthead on Mon, 24 July 2017 23:15
		Re: [GMCnet] ONAN starting about 2 K windings By: William Shourt on Mon, 24 July 2017 23:23
		Re: ONAN starting about 2 K windings By: Ken Burton on Mon, 24 July 2017 23:19
		Re: ONAN starting about 2 K windings By: Ken Burton on Tue, 25 July 2017 01:15
		Re: [GMCnet] ONAN starting about 2 K windings By: Ken Henderson on Tue, 25 July 2017 06:14
		Re: ONAN starting By: bwevers on Tue, 25 July 2017 00:22

Previous Topic:	Tank sending units
Next Topic:	403 passenger side exhaust manifold needed in midwest

Goto Forum:

-=] Back to Top [=-

Current Time: Mon Apr 29 08:17:52 CDT 2024

Total time taken to generate the page: 0.01145 seconds