GMCforum: GMCnet » ONAN starting

Home » Public Forums » GMCnet » ONAN starting (starter stays engaged after starting)

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] ONAN starting [message #321079 is a reply to message #321057]

Tue, 25 July 2017 15:11

Ken Burton

Messages: 10030
Registered: January 2004
Location: Hebron, Indiana

Karma:

Senior Member

I do not think that I would be chasing the resistor value on the Dino board. That resister is in series with the relay coil of K2, not K1 that we are working on. If K2 was not working there would be no power to the ignition or fuel pump and the engine would die due to lack of fuel an ignition.

Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana

Report message to a moderator

[Message index]

		ONAN starting By: Bill Shourt on Fri, 21 July 2017 14:04
		Re: [GMCnet] ONAN starting By: James Hupy on Fri, 21 July 2017 14:49
		Re: [GMCnet] ONAN starting By: William Shourt on Fri, 21 July 2017 18:15
		Re: [GMCnet] ONAN starting By: Carl S. on Fri, 21 July 2017 19:09
		Re: [GMCnet] ONAN starting By: William Shourt on Fri, 21 July 2017 19:17
		Re: ONAN starting By: lqqkatjon on Fri, 21 July 2017 22:35
		Re: ONAN starting By: Ken Burton on Sat, 22 July 2017 04:11
		Re: [GMCnet] ONAN starting By: Mr ERFisher on Sat, 22 July 2017 04:49
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 07:51
		Re: [GMCnet] ONAN starting By: Ken Burton on Sat, 22 July 2017 10:54
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 13:29
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 14:07
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 14:48
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 13:46
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sat, 22 July 2017 18:00
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 19:09
		Re: [GMCnet] ONAN starting By: bwevers on Sat, 22 July 2017 20:32
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sat, 22 July 2017 22:51
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sun, 23 July 2017 09:53
		Re: [GMCnet] ONAN starting By: William Shourt on Sun, 23 July 2017 18:17
		Re: [GMCnet] ONAN starting By: Guy Lopes on Tue, 25 July 2017 00:51
		Re: [GMCnet] ONAN starting By: Bruce Hart on Tue, 25 July 2017 05:59
		Re: [GMCnet] ONAN starting By: Ken Henderson on Tue, 25 July 2017 06:09
		Re: [GMCnet] ONAN starting By: jimk on Tue, 25 July 2017 10:03
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:23
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:29
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:32
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 14:19
		Re: [GMCnet] ONAN starting By: Ken Burton on Tue, 25 July 2017 15:11
		Re: [GMCnet] ONAN starting By: Emery Stora on Tue, 25 July 2017 20:30
		Re: [GMCnet] ONAN starting By: Ken Henderson on Tue, 25 July 2017 21:15
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 07:57
		Re: ONAN starting By: lqqkatjon on Sat, 22 July 2017 15:32
		Re: ONAN starting By: Ken Burton on Sat, 22 July 2017 20:14
		Re: ONAN starting By: JohnL455 on Sun, 23 July 2017 16:34
		Re: ONAN starting By: JohnL455 on Sun, 23 July 2017 16:38
		Re: ONAN starting By: Ken Burton on Sun, 23 July 2017 21:17
		Re: [GMCnet] ONAN starting By: William Shourt on Sun, 23 July 2017 23:09
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sun, 23 July 2017 23:35
		Re: ONAN starting about 2 K windings By: Matt Colie on Mon, 24 July 2017 09:28
		Re: [GMCnet] ONAN starting about 2 K windings By: William Shourt on Mon, 24 July 2017 13:26
		Re: [GMCnet] ONAN starting about 2 K windings By: Ken Henderson on Mon, 24 July 2017 20:56
		Re: [GMCnet] ONAN starting about 2 K windings By: Bullitthead on Mon, 24 July 2017 23:15
		Re: [GMCnet] ONAN starting about 2 K windings By: William Shourt on Mon, 24 July 2017 23:23
		Re: ONAN starting about 2 K windings By: Ken Burton on Mon, 24 July 2017 23:19
		Re: ONAN starting about 2 K windings By: Ken Burton on Tue, 25 July 2017 01:15
		Re: [GMCnet] ONAN starting about 2 K windings By: Ken Henderson on Tue, 25 July 2017 06:14
		Re: ONAN starting By: bwevers on Tue, 25 July 2017 00:22

Previous Topic:	Tank sending units
Next Topic:	403 passenger side exhaust manifold needed in midwest

Goto Forum:

-=] Back to Top [=-

Current Time: Thu May 16 12:28:04 CDT 2024

Total time taken to generate the page: 0.01023 seconds