| Don Browns Barn Sale [message #304841] |
Wed, 03 August 2016 14:46  |
powerjon
Messages: 2446
Registered: January 2004
Karma:
|
Senior Member |
|
|
Don has sold his GMC.
He needs to clean out all of the spare parts that he has collected over the years. You should contact Don directly, phone number is near the bottom of this message.
Don Brown's Barn Sale!
Don has sold his GMC Motor Home and now needs to sell all the GMC Parts in his barn.
Item # Item for Sale
1 1- Steering gearbox rebuilt (in box) $345
2 1- 1978 GMC motor home transmission overhauled by Redinbo Trans, Laf.IN with
Torque Converter 1-QB-3H/D rebuilt by Quality Torque Converts Inc. $1175 complete assy.
3 1- 1967 Olds-Variable-Pitch Transmission. Modified & overhauled by Redinbo. $1595
4 1- 1967 variable-Pitch Modified by Redinbo has 60,000 on it and was running good. $650
5 1- Special built engine by Cuppy is backup for fuel injection engine in my MN. 9.8-1 corn. ratio. New
in sealed box. Spec Sheet available at: $4200
6 1- New Master cylinder (in box). $50
7 1- New Air Tank (new in box). 1+ gallon in size, will fit GMC $70
8 1- New Flo-jet water pump. (New in box) P/N 04406-143K $80
9 (1)-Good Used Flo-Jet water pump model # 4406-143 $45
10 3- Torque Converters 3-QB-2 rebuilt by Quality Torque Converts Inc. (in the box) $298 each
11 1 set- L & R knuckles rebuilt by Ken Thoma. $230 each side $460 for the set
12 1 set used L&R Knuckles little wear. $125 each side $250 for the set
13 2- New Bi!stein Shocks for rear B46-0950 (in boxes) $80
14 1- Rebuilt 455 Water Pump. (in box) $85
15 1- set relined brake shoes for rear wheels new (in box ) $30
16 2- rear brake drums turned and ready (in boxes ) $125
17 1- New bushing kits for A-Frame K5222 $70
18 1- K6215 lower ball joint in the box. $95
19 4- Inner and 4 Outer CV Joints from Autos, very good condition. Each set consist of an inner and
outer CV joints $100 each set
20 L & R seal kit P/N t2422 new. (Tinker 416273 wheel seals) $12 for the set.
23. 1- 3.07 to 1- final drive rebuilt in crate $550
22 Item 22 sold
23 2- Weld Aluminum 16.5 inch Wheels one with tire mounted. $110 each
24 HD Trolly style Engine lift for taking the engine out the top, used once. $300
25 1- HD Engine stand for working on engine. $90
26 1- Set of 455 rods. Used with oversize wrist pins. $80
27 11) Fel-Pro exhaust flanges $15 for set
28 (2) New Skinner Electric 2-way valves ( leveling) #2006 761 $100
29 (1) Set ARP head bolts new in box. $90
30 (1) Vacuum control VC218 new $20
31 (2) New Rear 8 bolt hubs $275 each
32 (3) Sets Front Wheel Bearings A-23 +15103s + seals 1523 and 5109 new in boxes. $140
33 (2) Rear Wheel Bearings (2) #LM1349 new in boxes. and (2) #1310 $50 each
34 (4) Seal # 89745 new in boxes. $7
35 Rear wheel bearings (3) #15243 new in boxes. $60
36 (1) Rear bearing lock nut socket needed to replace rear bearings. 23/4 inch. ????
37 (1) Micro Precision Wheel balancer Model M-76 with GMC mounting hub. $235
38 Item removed from list
39 (1) Drive axle inner CV joint boot, new. $20
Post date is 8/2/2016
Call Don Brown at 765 427-6932
Give me a call and lets talk!
Engine Specs for Item#5
8/4/01
Engine & Heads 455 Olds
Block bored .030 oversize, using torque plate and micro finished for moly rings. Crankshaft turned to .010 under. Ford 460 rear main seal used.
Cloyes true roller timing chain.
TRW forged Pistons +.030 ( 9.4 - 1) compression ratio. Ductile Moly Rings.
All new Wrist pins, Rod and Main bearings.
Mondello Engle Cam # 16-18, lifters, and pushrods
Engine crank, pistons, rods, flex plate, etc. machine balanced. Oil galley restricters installed for improved crank shaft oiling.
HEADS
Ca heads with crossover welded closed at Indy for better HP. Crossover not needed with electronic fuel injection.
New hardend seats with 3 angle grind for improved flow.
One piece stainless steel valves. Intake opened to 2.070 Exhaust is stock 1.675 New valve springs
Using stock head gasket assembled engine calculates to be 9.8-1 compression ratio.
Contact Don direct, DO NOT contact me!
|
|
|
|
GMCforum
Search
Help
Register
Login
Home
