GMCforum: GMCnet » Bent bogie arm

Home » Public Forums » GMCnet » Bent bogie arm

Show: Today's Messages :: Polls :: Message Navigator

Re: Bent bogie arm [message #245386 is a reply to message #245381]

Thu, 27 March 2014 18:38

Ken Burton

Messages: 10030
Registered: January 2004
Location: Hebron, Indiana

Karma:

Senior Member

Get a 5 or 6 feet long straight edge. An aluminum measuring stick from Home Depot, Lowes, Menards, or the home supply store of your choice works well. Jack up the coach with no air in the bag on the right rear only. Remove the wheels and place the straight edge across the two hubs. You will immediately be able to see just how far out of line the wheel is. Take a porta-power, or small hydraulic jack, and place it between the frame and the back of of the arm and start jacking. I would reenforce the frame area where the jack sits with something. A piece of metal or even wood to spread out the force will work. Start jacking out until you get it straight again. You will have to go past the point of being straight because it will spring back some when the jack is removed.

At one rally I attended someone had a screw type device that worked well. We probably did about 15 coaches there including mine.

It is not a difficult job. It takes probably 1 hour. Most of the time is spent taking off and reinstalling the wheels.

Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana

Report message to a moderator

[Message index]

		Bent bogie arm By: 77PBFinland on Thu, 27 March 2014 16:33
		Re: Bent bogie arm By: appie on Thu, 27 March 2014 16:41
		Re: Bent bogie arm By: GMC Cruse on Thu, 27 March 2014 17:04
		Re: Bent bogie arm By: C Boyd on Thu, 27 March 2014 17:14
		Re: Bent bogie arm By: Loffen on Thu, 27 March 2014 18:14
		Re: Bent bogie arm By: Ken Burton on Thu, 27 March 2014 18:38
		Re: [GMCnet] Bent bogie arm By: k2gkk on Fri, 28 March 2014 09:59
		Re: [GMCnet] Bent bogie arm By: Little Yimmy on Fri, 28 March 2014 10:08
		Re: [GMCnet] Bent bogie arm By: james Ernst on Fri, 28 March 2014 10:48
		Re: [GMCnet] Bent bogie arm By: Billy Massey on Thu, 27 March 2014 19:49
		Re: [GMCnet] Bent bogie arm By: USAussie on Thu, 27 March 2014 19:59
		Re: Bent bogie arm By: Bob de Kruyff on Thu, 27 March 2014 19:56
		Re: [GMCnet] Bent bogie arm By: Kingsley Coach on Thu, 27 March 2014 20:21
		Re: [GMCnet] Bent bogie arm By: corleyw on Thu, 27 March 2014 21:24
		Re: [GMCnet] Bent bogie arm By: USAussie on Thu, 27 March 2014 22:35
		Re: [GMCnet] Bent bogie arm By: Bob de Kruyff on Thu, 27 March 2014 22:56
		Re: [GMCnet] Bent bogie arm By: corleyw on Fri, 28 March 2014 11:37
		Re: [GMCnet] Bent bogie arm By: USAussie on Fri, 28 March 2014 17:45
		Re: Bent bogie arm By: kerry pinkerton on Fri, 28 March 2014 07:27
		Re: [GMCnet] Bent bogie arm By: Ken Henderson on Thu, 27 March 2014 22:49
		Re: [GMCnet] Bent bogie arm By: gbarrow2 on Fri, 28 March 2014 11:35
		Re: [GMCnet] Bent bogie arm By: roy1 on Fri, 28 March 2014 11:45
		Re: [GMCnet] Bent bogie arm By: dwayne jacobson[1] on Fri, 28 March 2014 12:04
		Re: [GMCnet] Bent bogie arm By: gbarrow2 on Fri, 28 March 2014 12:08
		Re: [GMCnet] Bent bogie arm By: Mr ERFisher on Fri, 28 March 2014 12:05
		Re: [GMCnet] Bent bogie arm By: Ken Henderson on Fri, 28 March 2014 12:13
		Re: [GMCnet] Bent bogie arm By: A Hamilto on Fri, 28 March 2014 12:27
		Re: [GMCnet] Bent bogie arm By: roy1 on Fri, 28 March 2014 14:48
		Re: [GMCnet] Bent bogie arm By: gbarrow2 on Fri, 28 March 2014 14:29
		Re: [GMCnet] Bent bogie arm By: Ken Burton on Sat, 29 March 2014 00:47
		Re: [GMCnet] Bent bogie arm By: Ken Burton on Sat, 29 March 2014 01:13
		Re: [GMCnet] Bent bogie arm By: gbarrow2 on Sat, 29 March 2014 08:11
		Re: [GMCnet] Bent bogie arm By: John Olson on Sat, 29 March 2014 10:55
		Re: [GMCnet] Bent bogie arm By: A Hamilto on Sat, 29 March 2014 11:29
		Re: [GMCnet] Bent bogie arm By: 77PBFinland on Sun, 31 January 2016 12:20
		Re: [GMCnet] Bent bogie arm By: roy1 on Sun, 31 January 2016 12:32
		Re: [GMCnet] Bent bogie arm By: jimk on Sun, 31 January 2016 18:32
		Re: [GMCnet] Bent bogie arm By: Ken Henderson on Sun, 31 January 2016 19:51
		Re: [GMCnet] Bent bogie arm By: Ken Burton on Sat, 29 March 2014 11:41
		Re: [GMCnet] Bent bogie arm By: James Hupy on Sat, 29 March 2014 11:52
		Re: [GMCnet] Bent bogie arm By: Ken Burton on Sat, 29 March 2014 17:04
		Re: [GMCnet] Bent bogie arm By: James Hupy on Sat, 29 March 2014 18:00
		Re: [GMCnet] Bent bogie arm By: Ken Henderson on Sat, 29 March 2014 18:49
		Re: Bent bogie arm By: 77PBFinland on Fri, 28 March 2014 15:33
		Re: [GMCnet] Bent bogie arm By: USAussie on Fri, 28 March 2014 17:50
		Re: [GMCnet] Bent bogie arm By: corleyw on Fri, 28 March 2014 22:18
		Re: [GMCnet] Bent bogie arm By: Guy Lopes on Sat, 29 March 2014 13:26
		Re: Bent bogie arm By: Loffen on Fri, 28 March 2014 18:23
		Re: Bent bogie arm By: 77PBFinland on Sat, 29 March 2014 12:17
		Re: [GMCnet] Bent bogie arm By: USAussie on Sat, 29 March 2014 19:08
		Re: Bent bogie arm By: Ken Burton on Sat, 29 March 2014 19:42
		Re: [GMCnet] Bent bogie arm By: USAussie on Sat, 29 March 2014 21:31
		Re: [GMCnet] Bent bogie arm By: Ken Burton on Sat, 29 March 2014 22:52
		Re: [GMCnet] Bent bogie arm By: USAussie on Sat, 29 March 2014 23:30
		Re: [GMCnet] Bent bogie arm By: mickeysss on Sat, 29 March 2014 23:57
		Re: [GMCnet] Bent bogie arm By: Ken Burton on Sun, 30 March 2014 00:51
		Re: Bent bogie arm By: 77PBFinland on Sun, 30 March 2014 04:09
		Re: [GMCnet] Bent bogie arm By: Olly Schmidt on Sun, 30 March 2014 04:18
		Re: [GMCnet] Bent bogie arm By: Jerry Wheeler on Sun, 30 March 2014 07:31
		Re: [GMCnet] Bent bogie arm By: Ken Burton on Sun, 30 March 2014 08:43
		Re: Bent bogie arm By: JohnL455 on Sun, 31 January 2016 19:44
		Re: Bent bogie arm By: JohnL455 on Sun, 31 January 2016 19:54
		Re: [GMCnet] Bent bogie arm By: powwerjon on Sun, 31 January 2016 20:36
		Re: [GMCnet] Bent bogie arm By: jimk on Sun, 31 January 2016 21:25

Previous Topic:	replacement of stock interior drawer slides
Next Topic:	Re: [GMCnet] Transmission fluid leaking by the governor.

Goto Forum:

-=] Back to Top [=-

Current Time: Sat May 18 05:50:33 CDT 2024

Total time taken to generate the page: 0.01044 seconds