GMCforum: GMCnet » [GMCnet] block off plates

Home » Public Forums » GMCnet » [GMCnet] block off plates

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] block off plates [message #208768 is a reply to message #208765]

Sat, 25 May 2013 14:16

hnielsen2

Messages: 1434
Registered: February 2004
Location: Alpine CA

Karma:

Senior Member

Yes cut with a thin blade or case cutter.
Do not pry.
Things will brake
Howard

All is well with my Lord

On May 25, 2013, at 10:09 AM, Charles Boyd <covered-wagon@comcast.net> wrote:

>
>
> Sir: I would suggest a good small pry bar such as a lady finger. Try to pry on non gasket areas. Do not drive a screw driver between a gasket area. If you have to, drive a thin putty knife to break seal. Might use a razor knife to cut the ends.
>
>
> Kathy and Fred Estabr wrote on Sat, 25 May 2013 12:41
>> Help! I am in a world of hurt. Installed Springfield exhaust block off
>> plates and I guess one of the gaskets moved enough on installation that I
>> have a major water leak . The black RTV has now set so hard that I can't
>> get the manifold off. Any suggestions ??
>> Fred Estabrook
>> 76 Ell
>> Florence AZ
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
>
> --
> C. Boyd
> 76 Crestmont
> East Tennessee
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

All is well with my Lord

Report message to a moderator

[Message index]

		[GMCnet] block off plates By: Kathy and Fred Estabr on Sat, 25 May 2013 11:41
		Re: [GMCnet] block off plates By: C Boyd on Sat, 25 May 2013 12:09
		Re: [GMCnet] block off plates By: hnielsen2 on Sat, 25 May 2013 14:16
		Re: [GMCnet] block off plates By: Matt Colie on Sat, 25 May 2013 15:51
		Re: [GMCnet] block off plates By: USAussie on Sat, 25 May 2013 20:29
		Re: [GMCnet] block off plates By: WD0AFQ on Sat, 25 May 2013 21:36
		Re: [GMCnet] block off plates By: Kathy and Fred Estabr on Sat, 25 May 2013 22:37
		Re: [GMCnet] block off plates By: USAussie on Sun, 26 May 2013 10:02
		Re: [GMCnet] block off plates By: Kathy and Fred Estabr on Sun, 26 May 2013 13:03
		Re: [GMCnet] block off plates By: USAussie on Sun, 26 May 2013 20:40
		Re: [GMCnet] block off plates By: Kathy and Fred Estabr on Thu, 30 May 2013 10:59

Previous Topic:	[GMCnet] Tire Advice ~ Load Range
Next Topic:	[GMCnet] EZ Cool Firewall Insulation

Goto Forum:

-=] Back to Top [=-

Current Time: Tue May 28 13:48:15 CDT 2024

Total time taken to generate the page: 0.47089 seconds