GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.
Home » Public Forums » GMCnet » [GMCnet] Got Double Trouble weighed at a CAT Scale
Re: [GMCnet] Got Double Trouble weighed at a CAT Scale [message #181830 is a reply to message #181786] Sun, 26 August 2012 10:24 Go to previous messageGo to previous message
USAussie is currently offline  USAussie   United States
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma:
Senior Member
Hal,

Yes, I do have air pressure gauges on the OEM airbags; I'll take a look at them and post what they read. They are made in China so
their accuracy probably isn't that great. I bought a pair to replace them from McMaster Carr, they were Ashcroft and I figger'd they
were made in the USA - NOT - made in Brazil! I have yet to install them.

I should have mentioned that just before I left Houston John Sharpe and I reset the ride height to meet the manual specs. When I got
to Billy Young's place I checked it and it was a bit high on the driver side so I lowered it and both the front sides were in spec.
I have my torsion bar unloading tool with me and if time permits I can play with this at Amana. Is anyone bringing any scales?

I should have noted the following in my original message:

Under the front dinette seat I have three torque wrenches, the wheel bearing tool, another tool box with timing light, compression
gage, vacuum gage, drill set, tap and die set, and other misc tools. Then there's the six plastic divider boxes full of nuts, bolts,
screws, electrical stuff, and lots of miscellaneous bits and pieces. There's a soldering iron and a HF Dremel tool. I reckon
carrying all this crap is why the passenger side pork chop bolt is screwed in so far.

Under the rear dinette seat I have:

http://www.gmcmhphotos.com/photos/g5795-tool-box-installation.html

What's not in the picture above is the 1/2" electric impact wrench, the 1/2" battery powered drill (with three batteries), the 4"
grinder, Mapp gas bottle and small electric screwdriver.

One more thing - Double Trouble drives perfectly; if I am in the left lane of a three lane highway it will slowly creep off to the
left slowly, if I am in the middle lane it will go straight ahead, and if I am in the right lane it will creep off to the right
slowly.

Regards,
Rob

-----Original Message-----
From: Hal Kading

Rob,

Looks to me like you have diagonal unbalance. Passenger front and driver rear total 6560# and driver front and passenger rear total
5640# for an difference of 920#. Do you have air bag pressure gauges? It would be interesting to back off the passenger side torsion
adjusting bolt some and tighten the driver side an equal number of turns to see what that does to the bag pressures and weight
imbalance.

Hal

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426

Report message to a moderator

[Message index]
 
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: [GMCnet] Save those old starter solenoids. Or at least save the copper contact washers.
Next Topic: Body Pads
Goto Forum:
  


Current Time: Thu May 16 10:09:43 CDT 2024

Total time taken to generate the page: 0.05430 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.1.
Copyright ©2001-2021 FUDforum Bulletin Board Software