GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.
Home » Public Forums » GMCnet » [GMCnet] Why not
Re: [GMCnet] Why not [message #323994 is a reply to message #323959] Mon, 18 September 2017 16:52 Go to previous message
Ethan James is currently offline  Ethan James   United States
Messages: 32
Registered: October 2016
Location: Roanoke, VA
Karma:
Member
The same thing happened to me several time. The first time I didn't have
the plastic dial on and that piston came shooting out at me. Took a while
to find it, it had hit a plastic bin on the couch and ended up inside the
bin.

Mine don't leak at the valves anymore, but the T junction behind the drive
side one. I did adjust the tank pressure in my holding tank, I know it was
over 120psi (didn't let it get over 120 to find what it was stopping at),
now it's at 110-115psi. But I don't trust it to drive with it on, I
manually adjust the bags to around 80-90psi and use the cutoff at the
bags. I've given up on the old dials, just saving up money to replace them
with the JR Slaten ones and the run new lines.

--
Ethan James
Roanoke, VA
76' Glenbrook

On Sun, Sep 17, 2017 at 8:13 PM Robert J. Gogan
wrote:

> After rebuilding my rotary height control valves this spring, I was
> initially disappointed that my air springs were still leaking down. When I
> pulled
> the valves out of the dash and soap tested them, they had a slow leak
> around the newly installed housing seals.
> I torqued down the Allen screws and was delighted to see an airtight
> result. I had not cranked on the Allen bolts too hard previously because
> they
> seem somewhat delicate and the instructions warned about overtorqueing.
> The result was great!! The air springs have kept the coach up all summer.
> First time in 30 yrs of coach ownership that this has happened.
> However, today while driving, there was a loud pop that came from the
> passenger side rotary air valve and a loud whine of air leaking. I made it
> home
> before the suspension flattened out completely.
> At home, I discovered that the top piston had been blown out of the bore
> towards the plastic valve. I though this was no supposed to happen as it is
> retained by the rubber O ring on the spring side of the piston. The
> piston that was displaced out of the bore was inspected under the
> microscope.
> Both rubber O ring seals were in place and not damaged. The housing was
> inspected from outside and I could see no cracks. I thought I might have
> overtorqued the Allen screws and cracked the housing. Will have to
> disassemble the housing and see if there are internal cracks.
> My suspicion however is that the replacement O ring that goes on the
> spring side of the piston was undersized or not hard enough to prevent the
> air
> pressure from blowing the piston, that it was supposed to retain, out the
> front of the housing. Has any one else encountered this problem and come up
> with a solution?
> Bob Gogan
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

[Message index]
 
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: [GMCnet] lost gauges
Next Topic: [GMCnet] rookie errors.
Goto Forum:
  


Current Time: Sat May 18 20:59:44 CDT 2024

Total time taken to generate the page: 0.08529 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.1.
Copyright ©2001-2021 FUDforum Bulletin Board Software