| Kendra is looking for drawings for GMC cabinets [message #370093] |
Fri, 08 July 2022 10:28  |
 |
Matt Colie
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Copied from GMC Motorhomes forum.
Yesterday at 11:18 PM
Short term I'm fine with the original particle board cabinets. A bit rough but they get the job done.
Longer term I'd like to replace all the particle board with higher quality wood cabinets and fittings - in most cases following original measurements and layout. I don't have the skills to build these, so I'll need to take a set of drawings to a cabinet shop or boat interior specialist.
Has anyone found or created a detailed set of cabinet drawings based on the original GM 26' set?
I searched here, GMCMH Photos, GMCMI folders, etc.
thanks!
-Kendra
Kendra Fowles, Seattle, 1978 Kingsley
I these are in the files somewhere, I will forward the location to Kendra.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
| Re: Kendra is looking for drawings for GMC cabinets [message #370102 is a reply to message #370093] |
Sat, 09 July 2022 00:52  |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
There is a guy in Calgary, I forget his name at the moment, that use to make replacement cabinets out of aluminum. As soon a I remember his name I will post it. He should have the measurements you want.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
| [GMCnet] Re: Kendra is looking for drawings for GMC cabinets [message #370103 is a reply to message #370093] |
Sat, 09 July 2022 00:52 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
There is a guy in Calgary, I forget his name at the moment, that use to make replacement cabinets out of aluminum. As soon a I remember his name I
will post it. He should have the measurements you want.
--
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
| [GMCnet] Re: Kendra is looking for drawings for GMC cabinets [message #370107 is a reply to message #370103] |
Sun, 10 July 2022 00:30 |
 |
ljdavick
Messages: 3548
Registered: March 2007
Location: Fremont, CA
Karma: -3
|
Senior Member |
|
|
Was it Darren Paget? I remember he did this as a hobby - his focation was firefighter, if memory serves me.
Larry Davick
> On Jul 8, 2022, at 10:53 PM, Ken Burton Errors-To:Ken Burton Return-Path:Ken Burton X-Mailer:FUDforum v3.1.1 MIME-Version:1.0 Content-Type: text/plain@host.harmonylists.io; wrote:
>
> There is a guy in Calgary, I forget his name at the moment, that use to make replacement cabinets out of aluminum. As soon a I remember his name I
> will post it. He should have the measurements you want.
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Larry Davick
A Mystery Machine
1976(ish) Palm Beach
Fremont, Ca
Howell EFI + EBL + Electronic Dizzy
|
|
|
|
| Re: [GMCnet] Re: Kendra is looking for drawings for GMC cabinets [message #370114 is a reply to message #370107] |
Sun, 10 July 2022 12:41 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Yes, that is who I was thinking about. He was a fireman in Calgary. He drove straight through from Calgary to attend one of our Eastern States rallies. He did the same thing on the way back. That is way more than I would ever attempt.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
|
|
GMCforum
Search
Help
Register
Login
Home
