Home » Public Forums » GMCnet » Ragusa Final Drive Sender
Ragusa Final Drive Sender [message #369668] |
Sun, 15 May 2022 22:37 |
Tom Katzenberger
Messages: 399 Registered: June 2019 Location: Kingsville, MD
Karma: 4
|
Senior Member |
|
|
Does anyone know the tread size for the regusa final drive temperature sender? Quarter inch or 3/8?
I bent mine with the woodblock supports when I jacked the motor home up. I am not looking forward to putting my finger over the hole to determine what thread size the sender was. I would rather buy the sender and do a quick switch out.
Thanks in advance for any help in this matter.
Take care all,
Tom K.
Tom & Oki Katzenberger,
Kingsville, Maryland,
1977 23' Birchaven, 455 C.I.D., Micro Level, Howell EBL-EFI Spark Control, Macerator, York Air Compressor, 6 Wheel Disc, Quadra Bag, Onan W/Bovee Ignition
|
|
|
Re: Ragusa Final Drive Sender [message #369673 is a reply to message #369668] |
Mon, 16 May 2022 09:58 |
Scott Nutter
Messages: 781 Registered: January 2015 Location: Houston/San Diego
Karma: 4
|
Senior Member |
|
|
Tom, call Ragusa directly. They are very good at their customer service. 949-261-5898
Scott.
Scott Nutter
1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final drive, Quad bags, Dave Lenzi super duty mid axle disc brakes, tankless water heater, everything Lenzi. Alex Ferrera installed MSD Atomic EFI
Houston, Texas
|
|
|
Re: Ragusa Final Drive Sender [message #369677 is a reply to message #369668] |
Mon, 16 May 2022 14:32 |
Tom Katzenberger
Messages: 399 Registered: June 2019 Location: Kingsville, MD
Karma: 4
|
Senior Member |
|
|
Will do, Thank you Scott.
Tom & Oki Katzenberger,
Kingsville, Maryland,
1977 23' Birchaven, 455 C.I.D., Micro Level, Howell EBL-EFI Spark Control, Macerator, York Air Compressor, 6 Wheel Disc, Quadra Bag, Onan W/Bovee Ignition
|
|
|
Re: Ragusa Final Drive Sender [message #369678 is a reply to message #369668] |
Mon, 16 May 2022 14:59 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
I realize it takes a bit of contortion, but why not just drain it down a ways into a clean container and then pour it back when the sender is replaced?
--johnny
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: Ragusa Final Drive Sender [message #369679 is a reply to message #369668] |
Mon, 16 May 2022 16:02 |
Tom Katzenberger
Messages: 399 Registered: June 2019 Location: Kingsville, MD
Karma: 4
|
Senior Member |
|
|
Johnny, absolutely easy to do, But my better thought was that I could purchase one now then climb under there once and knock it all out. I have learned that you can be surprised how much knowledge some people have on hand.. I thought one may have known the thread sized for that center. No worries, as I purchased it once already I'm old just call ragusaAnd do the same again.
Tom & Oki Katzenberger,
Kingsville, Maryland,
1977 23' Birchaven, 455 C.I.D., Micro Level, Howell EBL-EFI Spark Control, Macerator, York Air Compressor, 6 Wheel Disc, Quadra Bag, Onan W/Bovee Ignition
|
|
|
Re: Ragusa Final Drive Sender [message #369680 is a reply to message #369668] |
Mon, 16 May 2022 16:07 |
Tom Katzenberger
Messages: 399 Registered: June 2019 Location: Kingsville, MD
Karma: 4
|
Senior Member |
|
|
Just to complete the info for the archive, I just called Ragusa per Scott's advise and they were great. I was told it is a 1/4 thread tap. I assume NPT.
Thank all and take care,
Tom K.
Tom & Oki Katzenberger,
Kingsville, Maryland,
1977 23' Birchaven, 455 C.I.D., Micro Level, Howell EBL-EFI Spark Control, Macerator, York Air Compressor, 6 Wheel Disc, Quadra Bag, Onan W/Bovee Ignition
|
|
|
Goto Forum:
Current Time: Mon Apr 29 00:17:03 CDT 2024
Total time taken to generate the page: 0.00909 seconds
|