Home » Public Forums » GMCnet » Carb fuel filters
Carb fuel filters [message #327121] |
Thu, 14 December 2017 23:19 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
A note on the fuel filter inside the 455 or 403 carb.
It turns out that there are 2 different filter listed both by Ac Delco and Wix. In 1976 GM changed ALL filters of this type in all vehicles using that filter. The change was adding a little rubber flapper check valve on the entrance side of the filter.
Either filter will fit in all years of our 455 and 403 engines with Quadrajet carbs.
AC Delco GF441 or Wix 33048 is the one without the check valve. (pre 1976)
AC Delco GF471 or Wix 33052 is the later version with the internal check valve and cost $1.80 more. (listed as 1976 and later)
I did not check out other brands and I also have no recommendation on which version to use.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
[Updated on: Sun, 17 December 2017 21:58] Report message to a moderator
|
|
|
|
Re: [GMCnet] Carb fuel filterst [message #327131 is a reply to message #327129] |
Fri, 15 December 2017 11:10 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
The most important thing is to have them with you and have a line wrench to
undo the fitting without rounding the fitting
On Fri, Dec 15, 2017 at 8:38 AM John Wright wrote:
> Here are some good pictures of the fuel filter and how it is installed.
> You can put them in backwards, ask me how I know!
>
> http://www.gmcmhphotos.com/photos/general-pictures/p58270-img-07751.html
> http://www.gmcmhphotos.com/photos/general-pictures/p58271-img-07761.html
>
> http://www.gmcmhphotos.com/photos/general-pictures/p58269-fuel-system-q-jet.html
>
> http://www.gmcmhphotos.com/photos/general-pictures/p58268-q-jet-fuel-filter.html
>
> J.R. Wright
> GMC GreatLaker 18 Year Member
> GMCGL Tech Editor
> GMC Eastern States Charter Member
> GMCMI 18 Year Member
> 78 Buskirk 30' Stretch
> 1975 Avion (Under Reconstruction)
> Michigan
>
>> On Dec 14, 2017, at 10:19 PM, Ken Burton wrote:
>>
>> A note on the fuel filter inside the 455 or 403 carb.
>>
>> It turns out that there are 2 different filter listed both by Ac Delco
> and Wix. In 1976 GM changed ALL filters of this type in all vehicles using
>> that filter. The change was adding a little rubber flapper check valve
> on the entrance side of the filter.
>>
>> Either filter will fit in all years of our 455 and 403 engines with
> Quadrajet carbs.
>>
>> AC Delco GF441 or Wix 33148 is the one without the check valve. (pre
> 1976)
>> AC Delco GF471 or Wix 33152 is the later version with the internal check
> valve and cost $1.80 more. (listed as 1976 and later)
>>
>> I did not check out other brands and I also have no recommendation on
> which version to use.
>> --
>> Ken Burton - N9KB
>> 76 Palm Beach
>> Hebron, Indiana
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] Carb fuel filterst [message #327140 is a reply to message #327131] |
Fri, 15 December 2017 13:59 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
AND be careful not to cross thread the fitting when you screw it back into the carb!
Regards,
Rob M.
The Pedantic Mechanic
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
USA '77 Kingsley - TZE 267V100808
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Jim Kanomata
Sent: Saturday, December 16, 2017 4:11 AM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] Carb fuel filterst
The most important thing is to have them with you and have a line wrench to
undo the fitting without rounding the fitting
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
Re: [GMCnet] Carb fuel filters [message #327141 is a reply to message #327129] |
Fri, 15 December 2017 14:00 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
JR,
Good photos! This filter installs "backwards." When I say that filter are "supposed" to flow from the larger surface area "outside"
to the smaller surface area "inside." This filter is installed "backwards;" the flow enters on the "inside" and flows to the
"outside." It doesn't take a lot to plug it up!
That's why Ken Frey's idea of installing a filter in the rubber line that connects the metal line welded to the front crossmember
and the inlet to the mechanical fuel pump:
http://www.gmcmhphotos.com/photos/aa-miscellaneous-photos/p54750-fuel-pump-inlet-filter.html
Regards,
Rob M.
The Pedantic Mechanic
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
USA '77 Kingsley - TZE 267V100808
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of John Wright
Sent: Saturday, December 16, 2017 3:38 AM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] Carb fuel filters
Here are some good pictures of the fuel filter and how it is installed. You can put them in backwards, ask me how I know!
http://www.gmcmhphotos.com/photos/general-pictures/p58270-img-07751.html
http://www.gmcmhphotos.com/photos/general-pictures/p58271-img-07761.html
http://www.gmcmhphotos.com/photos/general-pictures/p58269-fuel-system-q-jet.html
http://www.gmcmhphotos.com/photos/general-pictures/p58268-q-jet-fuel-filter.html
J.R. Wright
GMC GreatLaker 18 Year Member
GMCGL Tech Editor
GMC Eastern States Charter Member
GMCMI 18 Year Member
78 Buskirk 30' Stretch
1975 Avion (Under Reconstruction)
Michigan
> On Dec 14, 2017, at 10:19 PM, Ken Burton wrote:
>
> A note on the fuel filter inside the 455 or 403 carb.
>
> It turns out that there are 2 different filter listed both by Ac Delco and Wix. In 1976 GM changed ALL filters of this type in
all vehicles using
> that filter. The change was adding a little rubber flapper check valve on the entrance side of the filter.
>
> Either filter will fit in all years of our 455 and 403 engines with Quadrajet carbs.
>
> AC Delco GF441 or Wix 33148 is the one without the check valve. (pre 1976)
> AC Delco GF471 or Wix 33152 is the later version with the internal check valve and cost $1.80 more. (listed as 1976 and later)
>
> I did not check out other brands and I also have no recommendation on which version to use.
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
Re: [GMCnet] Carb fuel filters [message #327143 is a reply to message #327129] |
Fri, 15 December 2017 14:26 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Wix must have seen the reversal problem. On the Wix version of this filter the back (non-entrance) side is manufactured slightly larger and will not go in backwards. I have two of the non-check valve versions (33148) here and both were made that way. I can not verify the the 33152 version is the same. I also have no idea what other brands have done.
powwerjon wrote on Fri, 15 December 2017 10:37Here are some good pictures of the fuel filter and how it is installed. You can put them in backwards, ask me how I know!
http://www.gmcmhphotos.com/photos/general-pictures/p58270-img-07751.html
http://www.gmcmhphotos.com/photos/general-pictures/p58271-img-07761.html
http://www.gmcmhphotos.com/photos/general-pictures/p58269-fuel-system-q-jet.html
http://www.gmcmhphotos.com/photos/general-pictures/p58268-q-jet-fuel-filter.html
J.R. Wright
GMC GreatLaker 18 Year Member
GMCGL Tech Editor
GMC Eastern States Charter Member
GMCMI 18 Year Member
78 Buskirk 30' Stretch
1975 Avion (Under Reconstruction)
Michigan
> On Dec 14, 2017, at 10:19 PM, Ken Burton wrote:
>
> A note on the fuel filter inside the 455 or 403 carb.
>
> It turns out that there are 2 different filter listed both by Ac Delco and Wix. In 1976 GM changed ALL filters of this type in all vehicles using
> that filter. The change was adding a little rubber flapper check valve on the entrance side of the filter.
>
> Either filter will fit in all years of our 455 and 403 engines with Quadrajet carbs.
>
> AC Delco GF441 or Wix 33148 is the one without the check valve. (pre 1976)
> AC Delco GF471 or Wix 33152 is the later version with the internal check valve and cost $1.80 more. (listed as 1976 and later)
>
> I did not check out other brands and I also have no recommendation on which version to use.
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: [GMCnet] Carb fuel filterst [message #327145 is a reply to message #327140] |
Fri, 15 December 2017 14:34 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
If the line does not easily start threading, I remove the 4 carb mounting bolts. (I believe they are 1/2") It takes about 30 seconds. Then the carb can move around a bit with everything else still still connected and allow easy starting of the threads.
DO NOT OVER TIGHTEN THE CARB MOUNTING BOLTS when reinstalling or you will warp and destroy the carb.
Ken B.
USAussie wrote on Fri, 15 December 2017 13:59AND be careful not to cross thread the fitting when you screw it back into the carb!
Regards,
Rob M.
The Pedantic Mechanic
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
USA '77 Kingsley - TZE 267V100808
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Jim Kanomata
Sent: Saturday, December 16, 2017 4:11 AM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] Carb fuel filterst
The most important thing is to have them with you and have a line wrench to
undo the fitting without rounding the fitting
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: [GMCnet] Carb fuel filters [message #327148 is a reply to message #327143] |
Fri, 15 December 2017 16:11 |
Will Albers
Messages: 183 Registered: November 2017 Location: Detroit MI (Belleville)
Karma: 2
|
Senior Member |
|
|
Any advantage to the non check valve version?
On Dec 15, 2017 3:27 PM, "Ken Burton" wrote:
> Wix must have seen the reversal problem. On the Wix version of this
> filter the back (non-entrance) side is manufactured slightly larger and
> will not
> go in backwards. I have two of the non-check valve versions (33148) here
> and both were made that way. I can not verify the the 33152 version is the
> same. I also have no idea what other brands have done.
>
> powwerjon wrote on Fri, 15 December 2017 10:37
>> Here are some good pictures of the fuel filter and how it is installed.
> You can put them in backwards, ask me how I know!
>>
>> http://www.gmcmhphotos.com/photos/general-pictures/p58270-img-07751.html
>> http://www.gmcmhphotos.com/photos/general-pictures/p58271-img-07761.html
>> http://www.gmcmhphotos.com/photos/general-pictures/
> p58269-fuel-system-q-jet.html
>> http://www.gmcmhphotos.com/photos/general-pictures/
> p58268-q-jet-fuel-filter.html
>>
>> J.R. Wright
>> GMC GreatLaker 18 Year Member
>> GMCGL Tech Editor
>> GMC Eastern States Charter Member
>> GMCMI 18 Year Member
>> 78 Buskirk 30' Stretch
>> 1975 Avion (Under Reconstruction)
>> Michigan
>>
>>> On Dec 14, 2017, at 10:19 PM, Ken Burton wrote:
>>>
>>> A note on the fuel filter inside the 455 or 403 carb.
>>>
>>> It turns out that there are 2 different filter listed both by Ac
> Delco and Wix. In 1976 GM changed ALL filters of this type in all vehicles
>>> using
>>> that filter. The change was adding a little rubber flapper check
> valve on the entrance side of the filter.
>>>
>>> Either filter will fit in all years of our 455 and 403 engines with
> Quadrajet carbs.
>>>
>>> AC Delco GF441 or Wix 33148 is the one without the check valve. (pre
> 1976)
>>> AC Delco GF471 or Wix 33152 is the later version with the internal
> check valve and cost $1.80 more. (listed as 1976 and later)
>>>
>>> I did not check out other brands and I also have no recommendation on
> which version to use.
>>> --
>>> Ken Burton - N9KB
>>> 76 Palm Beach
>>> Hebron, Indiana
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
>
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
1978 Palm Beach.
Detroit Michigan
|
|
|
|
Re: [GMCnet] Carb fuel filterst [message #327159 is a reply to message #327153] |
Fri, 15 December 2017 22:23 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Thanks, I was thinking it was 10 ft-pd but I did not know for sure, so I stated nothing in the posting.
12 it is!
Ken B.
USAussie wrote on Fri, 15 December 2017 18:14The spec is 12 ft lb.
Regards,
Rob M.
The Pedantic Mechanic
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
USA '77 Kingsley - TZE 267V100808
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Ken Burton
Sent: Saturday, December 16, 2017 7:35 AM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] Carb fuel filterst
If the line does not easily start threading, I remove the 4 carb mounting bolts. (I believe they are 1/2") It takes about 30
seconds. Then the
carb can move around a bit with everything else still still connected and allow easy starting of the threads.
DO NOT OVER TIGHTEN THE CARB MOUNTING BOLTS when reinstalling or you will warp and destroy the carb.
Ken B.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: [GMCnet] Carb fuel filters [message #327163 is a reply to message #327141] |
Fri, 15 December 2017 23:33 |
powwerjon
Messages: 849 Registered: March 2013
Karma: -2
|
Senior Member |
|
|
Rob,
I removed the internal filter out of my original carb on the 77 403 just
after I got it in 1998. I ran a 2 filter system and did convert to an
electric fuel system with a electric fuel pump just after the selector
valve. I ran a filter in the same spot that Ken F put his and one between
the selector and the pump. When I changed the filters, I put a new filter
at the carb end and move the one there to the spot before the fuel pump.
http://www.gmcmhphotos.com/photos/g3657-electric-fuel-pump-26amp-3b-filter.html
John
J.R. Wright
GMC Great Laker
GMC Eastern States
GMCMHI
TZE Zone Restorations
78 Buskirk Custom 30' Stretch
75 Avion (Under going Frame up Restoration)
On Fri, Dec 15, 2017 at 1:00 PM, Rob Mueller
wrote:
> JR,
>
> Good photos! This filter installs "backwards." When I say that filter are
> "supposed" to flow from the larger surface area "outside"
> to the smaller surface area "inside." This filter is installed
> "backwards;" the flow enters on the "inside" and flows to the
> "outside." It doesn't take a lot to plug it up!
>
> That's why Ken Frey's idea of installing a filter in the rubber line that
> connects the metal line welded to the front crossmember
> and the inlet to the mechanical fuel pump:
>
> http://www.gmcmhphotos.com/photos/aa-miscellaneous-
> photos/p54750-fuel-pump-inlet-filter.html
>
> Regards,
> Rob M.
> The Pedantic Mechanic
> Sydney, Australia
> AUS '75 Avion - The Blue Streak TZE365V100428
> USA '75 Avion - Double Trouble TZE365V100426
> USA '77 Kingsley - TZE 267V100808
>
>
> -----Original Message-----
> From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of John
> Wright
> Sent: Saturday, December 16, 2017 3:38 AM
> To: gmclist@list.gmcnet.org
> Subject: Re: [GMCnet] Carb fuel filters
>
> Here are some good pictures of the fuel filter and how it is installed.
> You can put them in backwards, ask me how I know!
>
> http://www.gmcmhphotos.com/photos/general-pictures/p58270-img-07751.html
> http://www.gmcmhphotos.com/photos/general-pictures/p58271-img-07761.html
> http://www.gmcmhphotos.com/photos/general-pictures/
> p58269-fuel-system-q-jet.html
> http://www.gmcmhphotos.com/photos/general-pictures/
> p58268-q-jet-fuel-filter.html
>
> J.R. Wright
> GMC GreatLaker 18 Year Member
> GMCGL Tech Editor
> GMC Eastern States Charter Member
> GMCMI 18 Year Member
> 78 Buskirk 30' Stretch
> 1975 Avion (Under Reconstruction)
> Michigan
>
>> On Dec 14, 2017, at 10:19 PM, Ken Burton wrote:
>>
>> A note on the fuel filter inside the 455 or 403 carb.
>>
>> It turns out that there are 2 different filter listed both by Ac Delco
> and Wix. In 1976 GM changed ALL filters of this type in
> all vehicles using
>> that filter. The change was adding a little rubber flapper check valve
> on the entrance side of the filter.
>>
>> Either filter will fit in all years of our 455 and 403 engines with
> Quadrajet carbs.
>>
>> AC Delco GF441 or Wix 33148 is the one without the check valve. (pre
> 1976)
>> AC Delco GF471 or Wix 33152 is the later version with the internal check
> valve and cost $1.80 more. (listed as 1976 and later)
>
>>
>> I did not check out other brands and I also have no recommendation on
> which version to use.
>> --
>> Ken Burton - N9KB
>> 76 Palm Beach
>> Hebron, Indiana
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: Carb fuel filters [message #327167 is a reply to message #327121] |
Sat, 16 December 2017 08:13 |
kingd
Messages: 592 Registered: June 2004
Karma: 2
|
Senior Member |
|
|
So how about someone getting a filter with the check valve and tossing it in a glass baby food jar
full of ethanol laced fuel and reporting back in 3 or 4 months about what has happened to the rubber check valve.
Alternatively, some one could try to find out from WIX Engineering if the flapper
is made from ethanol resistant material.
I think it's great that the WIX filter is made so it can't be installed backwards.
DAVE KING
lurker, wannabe
Toronto, Ontario, Canada
|
|
|
Re: Carb fuel filters [message #327179 is a reply to message #327121] |
Sat, 16 December 2017 15:00 |
Chris Tyler
Messages: 458 Registered: September 2013 Location: Odessa FL
Karma: 7
|
Senior Member |
|
|
Its tempting to simply eliminate the carb filter and go with an inline external filter as they are difficult to access. many a Qjet has been discarded with boogered threads when people have done it wrong.
BTW there is [or at least was] a kit to repair that.
I run an View -all pyrex glass filter at a low point before the fuel pump with fuel inlection rated hose and double clamps. THe plastic ones discolor with age and become opaque.This ebables a visual check of the filter and for water issues as welll as a easy drain point with the electric pump. Never had a leak; if it did it will leak on hte ground rather than hot engine components.
In the high performence world the filters are almost always removed as they are a fuel restriction at high flow [especialy the pressed brass pettet type]- more than we will ever need for our application though.
Problem is, stuff can still sloth of at the pump or line and you risk sticking the needle and seat.
For that reason I still have the paper element in place just in case- which with the pre filter should last a long time
76 Glenbrook
|
|
|
|
Re: [GMCnet] Carb fuel filters [message #327182 is a reply to message #327180] |
Sat, 16 December 2017 15:58 |
Richard Denney
Messages: 920 Registered: April 2010
Karma: 9
|
Senior Member |
|
|
Mac, I don't recall exactly what I used, but it looks something like a
Summit SUM-230123R:
https://www.summitracing.com/parts/sum-230123r
Generally, these are easy to service and use a fine enough element.
But I also have 10-micron inline metal-can filters back by the tanks (3/8"
hose fittings and much cheaper). This inline filter close to the carb has
not yet needed service in maybe 10 years.
Rick "not clear, but not needing to be" Denney
On Sat, Dec 16, 2017 at 4:18 PM D C _Mac_ Macdonald
wrote:
> Hi, Chris.
>
>
> Do you have a source and part number for that Pyrex bowl filter? Sounds
> like an excellent suggestion.
>
> D C "Mac" Macdonald
> Amateur Radio K2GKK
> Since 30 November '53
> USAF and FAA, Retired
> Member GMCMI & Classics
> Oklahoma City, OK
> "The Money Pit"
> TZE166V101966
> '76 ex-Palm Beach
> k2gkk + hotmail dot com
>
>
>
> ________________________________
> From: Gmclist on behalf of Chris Tyler dtyler11@tampabay.rr.com>
> Sent: Saturday, December 16, 2017 15:00
> To: gmclist@list.gmcnet.org
> Subject: Re: [GMCnet] Carb fuel filters
>
> Its tempting to simply eliminate the carb filter and go with an inline
> external filter as they are difficult to access. many a Qjet has been
> discarded
> with boogered threads when people have done it wrong.
> BTW there is [or at least was] a kit to repair that.
> I run an View -all Pyrex glass filter at a low point before the fuel pump
> with fuel injection rated hose and double clamps. The plastic ones discolor
> with age and become opaque. This enables a visual check of the filter and
> for water issues as well as a easy drain point with the electric pump. Never
> had a leak; if it did it will leak on the ground rather than hot engine
> components.
> In the high performance world the filters are almost always removed as
> they are a fuel restriction at high flow [especially the pressed brass
> pettet
> type]- more than we will ever need for our application though.
> Problem is, stuff can still sloth of at the pump or line and you risk
> sticking the needle and seat.
> For that reason I still have the paper element in place just in case-
> which with the pre filter should last a long time
> --
> 76 Glenbrook
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Rick Denney
73 x-Glacier 230 "Jaws"
Off-list email to rick at rickdenney dot com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Carb fuel filters [message #327183 is a reply to message #327180] |
Sat, 16 December 2017 16:06 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Chris,
I have run some of our trucks W/o the filer in the carb and rereted it as
pieces of rubber, metal and other debree managed to get into the carb.
Once I show you the easy way to change that filter, it is not bad at all.
Call me ad I'll tell you how.
On Sat, Dec 16, 2017 at 1:17 PM, D C _Mac_ Macdonald
wrote:
> Hi, Chris.
>
>
> Do you have a source and part number for that Pyrex bowl filter? Sounds
> like an excellent suggestion.
>
> D C "Mac" Macdonald
> Amateur Radio K2GKK
> Since 30 November '53
> USAF and FAA, Retired
> Member GMCMI & Classics
> Oklahoma City, OK
> "The Money Pit"
> TZE166V101966
> '76 ex-Palm Beach
> k2gkk + hotmail dot com
>
>
>
> ________________________________
> From: Gmclist on behalf of Chris Tyler dtyler11@tampabay.rr.com>
> Sent: Saturday, December 16, 2017 15:00
> To: gmclist@list.gmcnet.org
> Subject: Re: [GMCnet] Carb fuel filters
>
> Its tempting to simply eliminate the carb filter and go with an inline
> external filter as they are difficult to access. many a Qjet has been
> discarded
> with boogered threads when people have done it wrong.
> BTW there is [or at least was] a kit to repair that.
> I run an View -all Pyrex glass filter at a low point before the fuel pump
> with fuel injection rated hose and double clamps. The plastic ones discolor
> with age and become opaque. This enables a visual check of the filter and
> for water issues as well as a easy drain point with the electric pump. Never
> had a leak; if it did it will leak on the ground rather than hot engine
> components.
> In the high performance world the filters are almost always removed as
> they are a fuel restriction at high flow [especially the pressed brass
> pettet
> type]- more than we will ever need for our application though.
> Problem is, stuff can still sloth of at the pump or line and you risk
> sticking the needle and seat.
> For that reason I still have the paper element in place just in case-
> which with the pre filter should last a long time
> --
> 76 Glenbrook
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
|
Re: [GMCnet] Carb fuel filters [message #327187 is a reply to message #327186] |
Sat, 16 December 2017 18:23 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Ethanal is a very great cleaner and it is cleaning the tanks so well, that
even on the coaches that I have been useing have caught me off guard as the
residude from the tank, not particules, have coated the filters and caused
me to need to replace the filters.
Upon examining the filters, there is no sign of particulets, just a slight
residude that plug the filters.
I say, have tools and new filters with you to change on the go.
On Sat, Dec 16, 2017 at 3:48 PM, Tom Lins wrote:
> Chris Tyler wrote on Sat, 16 December 2017 16:00
>> Its tempting to simply eliminate the carb filter and go with an inline
> external filter as they are difficult to access.
>
>
>
> I would not do that!
> I had 2 large inline filters before the carb filter when bringing our new
> coach home at the begining of this month and I ended up having to change
> them all twice on the 1300 mile trip home.
> Which reminds me I should probably change them again, cheap insurance.
>
> Fram CG3389
>
>
>
>
>
> --
> Tom Lins
> Elkton, FL
> 77 GM Rear Twin
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] Carb fuel filters [message #327188 is a reply to message #327187] |
Sat, 16 December 2017 18:45 |
Richard Denney
Messages: 920 Registered: April 2010
Karma: 9
|
Senior Member |
|
|
I would say it depends on the condition of the tanks and lines. I replaced
my tanks with Cinnabar tanks in 2003 or so, and when I dropped them this
year, they were still spotless. I replaced my upstream inline filters at
the same time, and was able to blow through the old ones with nearly no
resistance.
There are many inline filters for 3/8" hoses, but I seek out those rated at
10-15 microns.
The AN-6 filter up by the carb is only 18" from the carb.
Rick "noting that most non-GM carbs didn't have integral filters" Denney
On Sat, Dec 16, 2017 at 7:23 PM Jim Kanomata wrote:
> Ethanal is a very great cleaner and it is cleaning the tanks so well, that
> even on the coaches that I have been useing have caught me off guard as the
> residude from the tank, not particules, have coated the filters and caused
> me to need to replace the filters.
> Upon examining the filters, there is no sign of particulets, just a slight
> residude that plug the filters.
> I say, have tools and new filters with you to change on the go.
>
> On Sat, Dec 16, 2017 at 3:48 PM, Tom Lins wrote:
>
>> Chris Tyler wrote on Sat, 16 December 2017 16:00
>>> Its tempting to simply eliminate the carb filter and go with an inline
>> external filter as they are difficult to access.
>>
>>
>>
>> I would not do that!
>> I had 2 large inline filters before the carb filter when bringing our new
>> coach home at the begining of this month and I ended up having to change
>> them all twice on the 1300 mile trip home.
>> Which reminds me I should probably change them again, cheap insurance.
>>
>> Fram CG3389
>>
>>
>>
>>
>>
>> --
>> Tom Lins
>> Elkton, FL
>> 77 GM Rear Twin
>>
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
>
>
> --
> Jim Kanomata
> Applied/GMC, Newark,CA
> jimk@appliedairfilters.com
> http://www.appliedgmc.com
> 1-800-752-7502
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Rick Denney
73 x-Glacier 230 "Jaws"
Off-list email to rick at rickdenney dot com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Carb fuel filters [message #327189 is a reply to message #327188] |
Sat, 16 December 2017 19:02 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Rick,
Where were you able to obtain the Micron ratings of each filters?
On Sat, Dec 16, 2017 at 4:45 PM, Richard Denney wrote:
> I would say it depends on the condition of the tanks and lines. I replaced
> my tanks with Cinnabar tanks in 2003 or so, and when I dropped them this
> year, they were still spotless. I replaced my upstream inline filters at
> the same time, and was able to blow through the old ones with nearly no
> resistance.
>
> There are many inline filters for 3/8" hoses, but I seek out those rated at
> 10-15 microns.
>
> The AN-6 filter up by the carb is only 18" from the carb.
>
> Rick "noting that most non-GM carbs didn't have integral filters" Denney
>
> On Sat, Dec 16, 2017 at 7:23 PM Jim Kanomata
> wrote:
>
>> Ethanal is a very great cleaner and it is cleaning the tanks so well,
> that
>> even on the coaches that I have been useing have caught me off guard as
> the
>> residude from the tank, not particules, have coated the filters and
> caused
>> me to need to replace the filters.
>> Upon examining the filters, there is no sign of particulets, just a
> slight
>> residude that plug the filters.
>> I say, have tools and new filters with you to change on the go.
>>
>> On Sat, Dec 16, 2017 at 3:48 PM, Tom Lins wrote:
>>
>>> Chris Tyler wrote on Sat, 16 December 2017 16:00
>>>> Its tempting to simply eliminate the carb filter and go with an
> inline
>>> external filter as they are difficult to access.
>>>
>>>
>>>
>>> I would not do that!
>>> I had 2 large inline filters before the carb filter when bringing our
> new
>>> coach home at the begining of this month and I ended up having to
> change
>>> them all twice on the 1300 mile trip home.
>>> Which reminds me I should probably change them again, cheap insurance.
>>>
>>> Fram CG3389
>>>
>>>
>>>
>>>
>>>
>>> --
>>> Tom Lins
>>> Elkton, FL
>>> 77 GM Rear Twin
>>>
>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>>
>>
>>
>> --
>> Jim Kanomata
>> Applied/GMC, Newark,CA
>> jimk@appliedairfilters.com
>> http://www.appliedgmc.com
>> 1-800-752-7502
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> --
> Rick Denney
> 73 x-Glacier 230 "Jaws"
> Off-list email to rick at rickdenney dot com
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Goto Forum:
Current Time: Thu May 09 19:12:36 CDT 2024
Total time taken to generate the page: 0.01939 seconds
|