Vent line to filler neck [message #325541] |
Sun, 29 October 2017 23:34 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Is the vent line going to the filler neck something special? I noticed yesterday that it has a crack at the top and has been leaking for quite a while. I have not taken it apart yet but it appears to be just 1/2" or so gasoline hose.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: Vent line to filler neck [message #325547 is a reply to message #325541] |
Mon, 30 October 2017 05:58 |
lqqkatjon
Messages: 2324 Registered: October 2010 Location: St. Cloud, MN
Karma: 5
|
Senior Member |
|
|
1/2" fuel hose in the wheel well. Metal down the frame and i think 3/8" to the tanks. Or 5/16". But I am guessing your 1/2" chunck is all that has not been renewed.
I would still buy gates barrier hose.
Jon Roche
75 palm beach
EBL EFI, manny headers, Micro Level, rebuilt most of coach now.
St. Cloud, MN
http://lqqkatjon.blogspot.com/
|
|
|
|
Re: [GMCnet] Vent line to filler neck [message #325565 is a reply to message #325551] |
Mon, 30 October 2017 11:31 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Ken, It has been only few years since the manufactures did not figure out
how to overcome the Ethanol deteriorating the older rubber, even few years
old.
Just use the Standard 1/2 " fuel line,make sure it is not the Old stock.
Since the 1/2 " does not move as much, you can easily get one couple years
old.
On Mon, Oct 30, 2017 at 6:49 AM, Matt Colie wrote:
> Ken,
>
> That piece and the couplers on the fill line are the only part that are
> not Gates Barrier. That has lasted 10 years so far. If I have to redo it,
> I
> will get something better.
>
> Matt
> --
> Matt & Mary Colie - '73 Glacier 23 - Members GMCMI, GMCGL, GMCES
> Electronically Controlled Quiet Engine Cooling Fan
> OE Rear Drum Brakes with Applied Control Arms
> SE Michigan - Twixt A2 and Detroit
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: Vent line to filler neck [message #325566 is a reply to message #325541] |
Mon, 30 October 2017 12:10 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Thanks everyone. Oreiliies shows it in stock locally. I'll measure it and go get a piece before I tear this one out. I wanted to make sure that it was not something unique to the GMC Like the filler tube (I believe 1") connect likes and elbow.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|