[GMCnet] Hub movement [message #324251] |
Fri, 22 September 2017 22:20 |
ron preston
Messages: 46 Registered: November 2016
Karma: 1
|
Member |
|
|
Hi all,
My hub on the drivers side moves in relation to the knuckle. (Disc moves
maybe .125" in relation to caliper.)
Can't find anything in the manual regarding this but don't think it
should considering the 140# torque required on the axle nut. (I had both
CV boots replaced by Jim K ~ 1500 miles ago.)
Just checking before I start taking things apart.
PS picked up the corrogated plastic for my headliner thanks for the advice
.
Thanks,
Ron Preston 75 Glenbrook
San José
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Hub movement [message #324256 is a reply to message #324251] |
Sat, 23 September 2017 00:20 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Ron,
Check the nut and if it's tight I'd say you've got a wheel bearing problem if the hub moves but the knuckle doesn't.
Regards,
Rob M.
The Pedantic Mechanic
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
USA '77 Kingsley - TZE 267V100808
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of ron preston
Sent: Friday, September 22, 2017 10:20 PM
To: gmclist@list.gmcnet.org
Subject: [GMCnet] Hub movement
Hi all,
My hub on the drivers side moves in relation to the knuckle. (Disc moves
maybe .125" in relation to caliper.)
Can't find anything in the manual regarding this but don't think it
should considering the 140# torque required on the axle nut. (I had both
CV boots replaced by Jim K ~ 1500 miles ago.)
Just checking before I start taking things apart.
PS picked up the corrogated plastic for my headliner thanks for the advice
.
Thanks,
Ron Preston 75 Glenbrook
San José
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
Re: [GMCnet] Hub movement [message #324277 is a reply to message #324256] |
Sat, 23 September 2017 18:06 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Ron,
We tighten the hub around 200 ft lbs .
The play is in the Knuckle. We do not like to nit pick so if the play is
minimal , we do not require the knuckle to be replaced.
We also check to see that the seal is not leaking, as if it is leaking , it
is generally from the loose knuckle.
Replacing the axle assembly does not contribute to play in the
knuckle,unless the nut was not tightened to 150 ft lbs.
On Fri, Sep 22, 2017 at 10:20 PM, Rob Mueller
wrote:
> Ron,
>
> Check the nut and if it's tight I'd say you've got a wheel bearing problem
> if the hub moves but the knuckle doesn't.
>
> Regards,
> Rob M.
> The Pedantic Mechanic
> Sydney, Australia
> AUS '75 Avion - The Blue Streak TZE365V100428
> USA '75 Avion - Double Trouble TZE365V100426
> USA '77 Kingsley - TZE 267V100808
>
>
> -----Original Message-----
> From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of ron
> preston
> Sent: Friday, September 22, 2017 10:20 PM
> To: gmclist@list.gmcnet.org
> Subject: [GMCnet] Hub movement
>
> Hi all,
> My hub on the drivers side moves in relation to the knuckle. (Disc moves
> maybe .125" in relation to caliper.)
> Can't find anything in the manual regarding this but don't think it
> should considering the 140# torque required on the axle nut. (I had both
> CV boots replaced by Jim K ~ 1500 miles ago.)
> Just checking before I start taking things apart.
> PS picked up the corrogated plastic for my headliner thanks for the advice
> .
> Thanks,
> Ron Preston 75 Glenbrook
> San José
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|