Home » Public Forums » GMCnet » Has anyone installed the sanden AC compressor kit from Applied?
Has anyone installed the sanden AC compressor kit from Applied? [message #323215] |
Sat, 02 September 2017 20:17 |
Scott Nutter
Messages: 781 Registered: January 2015 Location: Houston/San Diego
Karma: 4
|
Senior Member |
|
|
Has anyone installed the Sanden AC compressor and bracket /hose kit from Applied for the *455*? I put mine in today, but it's not even close to how the Sanden people recommend the install. They were showing spacers all over, but on my install I only used one spacer. Also they showed the tension bracket on the other side of the compressor than that is shown on the Applied website. But this must be GMC specific.
Everything is hooked up, but I haven't ran the engine yet to make sure the belts don't spin off. And I'm not going to spin up the clutch until I get freon in it.
So I quess I'm looking for someone who has already installed the kit, to make sure I haven't screwed up the install. Spacers? Or tension bracket placement.
To me it looks to be a big improvement ovet the A6 unit that I had to replace 2 times over the last 3 years. And with this redesigned bracket, I can actually change out the valve cover gaskets without pulling off the AC bracket and compressor!
Thanks,
Scott.
Scott Nutter
1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final drive, Quad bags, Dave Lenzi super duty mid axle disc brakes, tankless water heater, everything Lenzi. Alex Ferrera installed MSD Atomic EFI
Houston, Texas
|
|
|
Re: [GMCnet] Has anyone installed the sanden AC compressor kit from Applied? [message #323217 is a reply to message #323215] |
Sat, 02 September 2017 20:38 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Scott,
We need to mock up the unit as a change was made about a year ago and we
did not edit the instructions.
Just because our guys can install them easily does not mean much, so we
need to get on it now.
Scott, I'll issue some credit on your account.
On Sat, Sep 2, 2017 at 6:17 PM, Scott Nutter wrote:
> Has anyone installed the Sanden AC compressor and bracket /hose kit from
> Applied for the *455*? I put mine in today, but it's not even close to how
> the Sanden people recommend the install. They were showing spacers all
> over, but on my install I only used one spacer. Also they showed the tension
> bracket on the other side of the compressor than that is shown on the
> Applied website. But this must be GMC specific.
>
> Everything is hooked up, but I haven't ran the engine yet to make sure the
> belts don't spin off. And I'm not going to spin up the clutch until I get
> freon in it.
> So I quess I'm looking for someone who has already installed the kit, to
> make sure I haven't screwed up the install. Spacers? Or tension bracket
> placement.
>
> To me it looks to be a big improvement ovet the A6 unit that I had to
> replace 2 times over the last 3 years. And with this redesigned bracket, I
> can
> actually change out the valve cover gaskets without pulling off the AC
> bracket and compressor!
>
> Thanks,
> Scott.
> --
> Scott Nutter
> 1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final
> drive, Quad bags, tankless water heater, everything Lenzi.
> Houston, Texas
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] Has anyone installed the sanden AC compressor kit from Applied? [message #323219 is a reply to message #323217] |
Sat, 02 September 2017 21:29 |
Scott Nutter
Messages: 781 Registered: January 2015 Location: Houston/San Diego
Karma: 4
|
Senior Member |
|
|
Jim,
No need to issue me a credit. Nothing was damaged or lacking quality of the product.
If the install that made the most sense to me was correct, then it was a very easy install.
I need to fill it up with freon and test it.
If no one chimes in on instructions, and/or mine is successful I can chart out the install for you. Like I said, it was a easy install.
But thanks for the offer.
Scott.
Scott Nutter
1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final drive, Quad bags, Dave Lenzi super duty mid axle disc brakes, tankless water heater, everything Lenzi. Alex Ferrera installed MSD Atomic EFI
Houston, Texas
|
|
|
Re: [GMCnet] Has anyone installed the sanden AC compressor kit from Applied? [message #323229 is a reply to message #323219] |
Sat, 02 September 2017 22:28 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
It still need better instruction for sure.
Lot of time, when you get too familiar, then we assume.
Thanks for the feedback.
On Sat, Sep 2, 2017 at 7:29 PM, Scott Nutter wrote:
> Jim,
> No need to issue me a credit. Nothing was damaged or lacking quality of
> the product.
>
> If the install that made the most sense to me was correct, then it was a
> very easy install.
> I need to fill it up with freon and test it.
> If no one chimes in on instructions, and/or mine is successful I can chart
> out the install for you. Like I said, it was a easy install.
>
> But thanks for the offer.
> Scott.
> --
> Scott Nutter
> 1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final
> drive, Quad bags, tankless water heater, everything Lenzi.
> Houston, Texas
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] Has anyone installed the sanden AC compressor kit from Applied? [message #323299 is a reply to message #323229] |
Mon, 04 September 2017 12:11 |
Keith V
Messages: 2337 Registered: March 2008 Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
Just be VERY VERY careful of the bolts around the clutch.make sure they will not hit the AC hose or you will be doing it all over again.
remember the engine tourques over on load pushng the clutch closer to the hoses.
Been there have the tee shirt
Keith
________________________________
From: Gmclist on behalf of Jim Kanomata
Sent: Saturday, September 2, 2017 10:28:02 PM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] Has anyone installed the sanden AC compressor kit from Applied?
It still need better instruction for sure.
Lot of time, when you get too familiar, then we assume.
Thanks for the feedback.
On Sat, Sep 2, 2017 at 7:29 PM, Scott Nutter wrote:
> Jim,
> No need to issue me a credit. Nothing was damaged or lacking quality of
> the product.
>
> If the install that made the most sense to me was correct, then it was a
> very easy install.
> I need to fill it up with freon and test it.
> If no one chimes in on instructions, and/or mine is successful I can chart
> out the install for you. Like I said, it was a easy install.
>
> But thanks for the offer.
> Scott.
> --
> Scott Nutter
> 1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final
> drive, Quad bags, tankless water heater, everything Lenzi.
> Houston, Texas
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
|
Re: Has anyone installed the sanden AC compressor kit from Applied? [message #323482 is a reply to message #323215] |
Wed, 06 September 2017 23:57 |
Scott Nutter
Messages: 781 Registered: January 2015 Location: Houston/San Diego
Karma: 4
|
Senior Member |
|
|
Keith,
I was able to get a cover for the clutch on Amazon for $15. Should take care of the bolt saw problem. Although I did secure the hoses so contact should not be a issue.
JJ,
Yes, only one spacer is needed from the parts kit.
When I get back home on Friday, I will take it to a AC shop to have freon put in!! So far it's a great kit.
Scott
Scott Nutter
1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final drive, Quad bags, Dave Lenzi super duty mid axle disc brakes, tankless water heater, everything Lenzi. Alex Ferrera installed MSD Atomic EFI
Houston, Texas
|
|
|
Re: [GMCnet] Has anyone installed the sanden AC compressor kit from Applied? [message #323483 is a reply to message #323482] |
Thu, 07 September 2017 00:05 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Scott,
Most of us now refuse to use Freon. Duracool (HC12a) is much more
efficient, environment friendly, and cheaper. You can easily install it
yourself.
Ken H.
On Thu, Sep 7, 2017 at 12:57 AM, Scott Nutter wrote:
> ...
>
> When I get back home on Friday, I will take it to a AC shop to have freon
> put in!! So far it's a great kit.
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Has anyone installed the sanden AC compressor kit from Applied? [message #323485 is a reply to message #323482] |
Thu, 07 September 2017 00:35 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
WE mocked up the mount and compressor and now we have pictures to send with
each kit to clear up the mounting issue.
On Wed, Sep 6, 2017 at 9:57 PM, Scott Nutter wrote:
> Keith,
> I was able to get a cover for the clutch on Amazon for $15. Should take
> care of the bolt saw problem. Although I did secure the hoses so contact
> should not be a issue.
>
> JJ,
> Yes, only one spacer is needed from the parts kit.
>
> When I get back home on Friday, I will take it to a AC shop to have freon
> put in!! So far it's a great kit.
> Scott
> --
> Scott Nutter
> 1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final
> drive, Quad bags, tankless water heater, everything Lenzi.
> Houston, Texas
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Goto Forum:
Current Time: Thu Mar 28 06:50:14 CDT 2024
Total time taken to generate the page: 0.01999 seconds
|