How Do I Repair Ladder Screw Holes in Back Panel? [message #315955] |
Thu, 13 April 2017 01:05 |
bryhart
Messages: 90 Registered: July 2015 Location: Salem, OR
Karma: 0
|
Member |
|
|
The screws that were in there were already larger that the rest of the ladder screws. I assume someone stripped out the holes and put in larger screws as a "fix". I want to repair this and reinstall the ladder bracket in the same spot.
Any ideas?
1977 Palm Beach
|
|
|
|
|
Re: [GMCnet] How Do I Repair Ladder Screw Holes in Back Panel? [message #315961 is a reply to message #315959] |
Thu, 13 April 2017 07:24 |
Mr ERFisher
Messages: 7117 Registered: August 2005
Karma: 2
|
Senior Member |
|
|
On Thu, Apr 13, 2017 at 5:22 AM gene Fisher wrote:
> Read here
>
> http://www.dwinchester.com/GMC/
> Back hatch screw replacement
>
> On Thu, Apr 13, 2017 at 4:35 AM Jerry Wheeler
> wrote:
>
>> On my 78 Royale, the ladder screws just below the rear window were loose.
>> I was able to go inside and loosen the panel just below the window and put
>> a plate in there and used small ss bolts and nuts to attach the ladder at
>> that point; I did this in 2000 and have not had a problem since then.
>> JR Wheeler 78 Royale 73 Painted Desert NC/OR
>>
>> On Thu, Apr 13, 2017 at 2:05 AM, Bryan Hartman wrote:
>>
>>> The screws that were in there were already larger that the rest of the
>>> ladder screws. I assume someone stripped out the holes and put in larger
>>> screws
>>> as a "fix". I want to repair this and reinstall the ladder bracket in
>> the
>>> same spot.
>>>
>>> Any ideas?
>>>
>>> http://s148.photobucket.com/user/bryhart/media/GMC%20-%
>>> 20Conroe%20TX%201977%20Palm%20Beach/9ABB0143-81DE-4D71-
>>> B67E-DB25DFD0EECF.jpg.html
>>> --
>>> 1977 Palm Beach
>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> --
> Gene Fisher -- 74-23,77PB/ore/ca
> “Give a man a fish; you have fed him for today --- give him a URL and
> -------
> http://gmcmotorhome.info/
> Alternator Protection Cable
> http://gmcmotorhome.info/APC.html
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
|
Re: How Do I Repair Ladder Screw Holes in Back Panel? [message #315966 is a reply to message #315963] |
Thu, 13 April 2017 09:03 |
midlf
Messages: 2212 Registered: July 2007 Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
The ear plugs must be the porous type with open pores. Some ear plugs have a film converting the foam to prevent them from absorbing dirt, sweat, ear wax etc. Also prevents absorbing epoxy.
Larry wrote on Thu, 13 April 2017 08:05Dale Ropp has given several presentations at GMCMI conventions about the use of fiberglass for building and repair of GMC related stuff. One of his techniques for repairing holes like yours is to soak ear plugs....you know the type that you put in your ears when trap shooting.....soak them in fiberglass resin then stick them in the holes. They will try to expand to their original shape on the inside and outside of the hole. After the resin sets, just carefully sand off the outside flush, paint and redrill the hole. This technique puts a fairly big bung of cured resin inside the hole for support without having to take the inside of the coach apart. I've tried this on my coach were the screws pulled out and was difficult if not impossible to get at the inside to mount support. JWID
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
Re: How Do I Repair Ladder Screw Holes in Back Panel? [message #315971 is a reply to message #315966] |
Thu, 13 April 2017 10:19 |
Larry
Messages: 2875 Registered: January 2004 Location: Menomonie, WI
Karma: 10
|
Senior Member |
|
|
midlf wrote on Thu, 13 April 2017 09:03The ear plugs must be the porous type with open pores. Some ear plugs have a film converting the foam to prevent them from absorbing dirt, sweat, ear wax etc. Also prevents absorbing epoxy.
Larry wrote on Thu, 13 April 2017 08:05Dale Ropp has given several presentations at GMCMI conventions about the use of fiberglass for building and repair of GMC related stuff. One of his techniques for repairing holes like yours is to soak ear plugs....you know the type that you put in your ears when trap shooting.....soak them in fiberglass resin then stick them in the holes. They will try to expand to their original shape on the inside and outside of the hole. After the resin sets, just carefully sand off the outside flush, paint and redrill the hole. This technique puts a fairly big bung of cured resin inside the hole for support without having to take the inside of the coach apart. I've tried this on my coach were the screws pulled out and was difficult if not impossible to get at the inside to mount support. JWID
Thanks Steve, forgot to mention that.
Larry
78 Royale w/500 Caddy
Menomonie, WI.
|
|
|
Re: How Do I Repair Ladder Screw Holes in Back Panel? [message #315976 is a reply to message #315955] |
Thu, 13 April 2017 11:48 |
Adrien G.
Messages: 474 Registered: May 2008 Location: Burns Flat, OK 73624
Karma: 1
|
Senior Member |
|
|
Bryan, I used "Rivet Nuts for Plastic and Composites" from McMaster-Carr.
https://www.mcmaster.com/#rivets/=176j0fo
Use some epoxy to seal the head of the RN, and if the latter has a misalignment making the leg not sit right,
then bend or shim so as to not have any pull out force on the RN.
What I did.
Adrien & Jenny Genesoto
75 Glenbrook (26-3) Mods LS3.70 FD / Reaction Sys / 80mm Front&Intermidiate / Hydroboost / 16" Tires / Frame Rebuild / Interior Rebuild
Yuba City,Ca. Text 530-nine-3-three-3-nine-nine-6
|
|
|
Re: [GMCnet] How Do I Repair Ladder Screw Holes in Back Panel? [message #315978 is a reply to message #315976] |
Thu, 13 April 2017 12:40 |
Emery Stora
Messages: 959 Registered: January 2011
Karma: 4
|
Senior Member |
|
|
Or you can use well nuts as shown here.
https://www.amazon.com/s/?ie=UTF8&keywords=rubber+well+nuts&tag=googhydr-20&index=aps&hvadid=174242859760&hvpos=1t2&hvnetw=g&a mp;hvrand=9807577609909900246&hvpone=&hvptwo=&hvqmt=e&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9028880&hvtargid=aud-262039 897656:kwd-8244110557&ref=pd_sl_563vqj9fro_e
They work well and are self sealing. I have them holding the top of my ladder.
You will have to open the holes to 1/2” for the large screw/bolt that you will be using. They are very strong.
Emery Stora
77 Kingsley
Frederick, CO
> On Apr 13, 2017, at 10:48 AM, Adrien Genesoto wrote:
>
> Bryan, I used "Rivet Nuts for Plastic and Composites" from McMaster-Carr.
>
> https://www.mcmaster.com/#rivets/=176j0fo
>
> Use some epoxy to seal the head of the RN, and if the latter has a misalignment making the leg not sit right,
> then bend or shim so as to not have any pull out force on the RN.
>
> What I did.
>
>
> --
> ”When we avoid the mistakes we might have made, we sometimes make the mistakes that we might have avoided.”
>
>
>
> Adrien & Jenny Genesoto
> 75 Glenbrook 26-3
> Yuba City,Ca. Text 530-nine-3-three-3-nine-nine-6
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
|
|
|
Re: How Do I Repair Ladder Screw Holes in Back Panel? [message #316059 is a reply to message #316044] |
Sat, 15 April 2017 13:07 |
midlf
Messages: 2212 Registered: July 2007 Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
bryhart wrote on Fri, 14 April 2017 23:49pjburt wrote on Fri, 14 April 2017 15:46
Ahh yes. The old "I discovered more syndrome" I can relate. My sympathies.
Haha...you don't know the half of it.
Yeah - in old house restoration it''s called "the mushroom factor". I my shop it has been dubbed as "the ultimate project creep."
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
Re: How Do I Repair Ladder Screw Holes in Back Panel? [message #316217 is a reply to message #316200] |
Tue, 18 April 2017 10:14 |
midlf
Messages: 2212 Registered: July 2007 Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
Johnny Bridges wrote on Tue, 18 April 2017 08:01We always called it "You can't do just one thing"
--johnny
The dangerous phrase here is I"'ll do it while I'm in there".
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
Re: How Do I Repair Ladder Screw Holes in Back Panel? [message #316402 is a reply to message #315963] |
Fri, 21 April 2017 14:21 |
bhayes
Messages: 263 Registered: March 2010
Karma: 1
|
Senior Member |
|
|
Larry wrote on Thu, 13 April 2017 07:05Dale Ropp has given several presentations at GMCMI conventions about the use of fiberglass for building and repair of GMC related stuff. One of his techniques for repairing holes like yours is to soak ear plugs....you know the type that you put in your ears when trap shooting.....soak them in fiberglass resin then stick them in the holes. They will try to expand to their original shape on the inside and outside of the hole. After the resin sets, just carefully sand off the outside flush, paint and redrill the hole. This technique puts a fairly big bung of cured resin inside the hole for support without having to take the inside of the coach apart. I've tried this on my coach were the screws pulled out and was difficult if not impossible to get at the inside to mount support. JWID
This is a great idea. Not to hijack the thread, but has anyone tried doing something similar with the holes for the clearance lights? I've got a few rear clearance lights where the screw holes have gotten a little too large for the rivet nuts that I'm using on the rest of the coach, but still too small for the next size up.
Bryan Hayes
'76 Eleganza II
Salt Lake City, Utah
|
|
|
Re: How Do I Repair Ladder Screw Holes in Back Panel? [message #316408 is a reply to message #316402] |
Fri, 21 April 2017 14:48 |
lqqkatjon
Messages: 2324 Registered: October 2010 Location: St. Cloud, MN
Karma: 5
|
Senior Member |
|
|
Have
Not tried
It myself. But dale's presentation at chippawa falls stuck with me.
If the ear plug is big enough for the well nut hole it should work the same. Dale suggested for larger holds, use a sponge soaked in the epoxy.
Jon Roche
75 palm beach
EBL EFI, manny headers, Micro Level, rebuilt most of coach now.
St. Cloud, MN
http://lqqkatjon.blogspot.com/
|
|
|