GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.

Home » Public Forums » GMCnet » Plumbing question
Plumbing question [message #323700] Sun, 10 September 2017 12:00 Go to next message
trapper is currently offline  trapper   Canada
Messages: 52
Registered: April 2015
Location: Saskatchewan, Canada
Karma: 0
Member
I need to clean up the plumbing around the water tank and pump as it is a Hodge Podge of garden hose, rad hose, and gawd knows what else. I also want to put in a hot water bypass as well as an antifreeze line for winterizing.

Anyways my question is about how the fresh water hookup interfaces with the plumbing. Is there a one-way valve in the system? Or does the OEM pump have it built in? I'm thinking something might be in there as I had an issue the other week. I lost all water and my pump just kept going. After a crap load of debugging I saw water leaking out the fresh water hookup port. I 'pushed' the inside of it and water blasted out hard. After that my inside water returned to normal.

I really need to clean this up Smile


75 Glenbrook
Re: Plumbing question [message #323709 is a reply to message #323700] Sun, 10 September 2017 15:26 Go to previous messageGo to next message
Matt Colie is currently offline  Matt Colie   United States
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
Senior Member
trapper wrote on Sun, 10 September 2017 13:00
I need to clean up the plumbing around the water tank and pump as it is a Hodge Podge of garden hose, rad hose, and gawd knows what else. I also want to put in a hot water bypass as well as an antifreeze line for winterizing.

Anyways my question is about how the fresh water hookup interfaces with the plumbing. Is there a one-way valve in the system? Or does the OEM pump have it built in? I'm thinking something might be in there as I had an issue the other week. I lost all water and my pump just kept going. After a crap load of debugging I saw water leaking out the fresh water hookup port. I 'pushed' the inside of it and water blasted out hard. After that my inside water returned to normal.

I really need to clean this up Smile

Well, a good start would be to replace that city water connection. That is supposed to have a working check valve.

In the early coaches with copper water systems, there was a check valve at the water pump because those pumps could not handle the 70psi that exists in some places. I don't know about the non-copper coaches.

The one thing you should pay attention to is that the hose and other parts you put in there are "drinking water safe". That means that they limited the amount of lead and toxic chemicals that might come loose.

Matt


Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
Re: Plumbing question [message #323811 is a reply to message #323709] Tue, 12 September 2017 17:04 Go to previous message
trapper is currently offline  trapper   Canada
Messages: 52
Registered: April 2015
Location: Saskatchewan, Canada
Karma: 0
Member
Good advice thanks. I think I'll be replacing the external water connector regardless as I can't get it to stop leaking in the few times I have used it.

I do have a check valve by the pump...it is disconnected now but I can re-use it when I update the plumbing.

My valve on the floor to drain the water tank doesn't seem to do anything and is hard as heck to move. I assume this is to drain the water tank via gravity? Also looks like there is a valve that will allow you to drain via the pump?


75 Glenbrook
Previous Topic: [GMCnet] Irma email
Next Topic: [GMCnet] Need a GOOD relay to run my two fuel pumps. As my new China one just quit.
Goto Forum:
  


Current Time: Fri Mar 29 05:53:13 CDT 2024

Total time taken to generate the page: 0.00643 seconds