GMCforum: GMCnet » Cardone water pump AAZ-55-21118H

Home » Public Forums » GMCnet » Cardone water pump AAZ-55-21118H

Show: Today's Messages :: Polls :: Message Navigator

Cardone water pump AAZ-55-21118H [message #348903]

Fri, 04 October 2019 16:27

sandy trout

Messages: 51
Registered: October 2018
Location: texas

Karma: 1

Member

I just got an email from Summit Racing where I had the Cardone water pump AAZ-55-21118H on back order since April.
The told me they got word from manufacture that they were no long making the pump and the order was being cancelled.

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #348929 is a reply to message #348903]

Sat, 05 October 2019 10:30

Scott Nutter

Messages: 782
Registered: January 2015
Location: Houston/San Diego

Karma: 4

Senior Member

Sandy,
That's what we've been finding out. I've even called most pep boys supply houses in Texas to check on stock and none were found.
One option for a new water pump is the GMB "130-1260P". On Amazon.
Good luck, Scott.

Scott Nutter 1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final drive, Quad bags, Dave Lenzi super duty mid axle disc brakes, tankless water heater, everything Lenzi. Alex Ferrera installed MSD Atomic EFI Houston, Texas

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #348937 is a reply to message #348929]

Sat, 05 October 2019 15:21

sandy trout

Messages: 51
Registered: October 2018
Location: texas

Karma: 1

Member

Does that one have the heavy duty bearings in it?

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #348939 is a reply to message #348903]

Sat, 05 October 2019 17:06

Scott Nutter

Messages: 782
Registered: January 2015
Location: Houston/San Diego

Karma: 4

Senior Member

Yes, it does have the heavy duty roller bearings.
Scott.

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349022 is a reply to message #348903]

Mon, 07 October 2019 15:17

sandy trout

Messages: 51
Registered: October 2018
Location: texas

Karma: 1

Member

Thanks, Scott, I didn't see it on Amazon but I saw several GMB numbers that didn't match that one that said were heavy duty.
I'll dig a little deeper tonight for that number. I see Airtech sells some too that look a lot like the GMB.

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349030 is a reply to message #348903]

Mon, 07 October 2019 17:49

Scott Nutter

Messages: 782
Registered: January 2015
Location: Houston/San Diego

Karma: 4

Senior Member

Here you go Sandy.
GMB 130-1260P High Performance Series Water Pump with Gasket https://www.amazon.com/dp/B000JYFL6K/ref=cm_sw_r_cp_tai_8c8MDbBM48VSA

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349042 is a reply to message #348903]

Mon, 07 October 2019 19:32

jhbridges

Messages: 8412
Registered: May 2011
Location: Braselton ga

Karma: -74

Senior Member

Per the illustration in the url on eBay the shaft is in ball bearings at the nose. You want one with rollers for the front bearing to handle the asymmetric belt load(s). The Cardone one has the letter H appended to the part number, all of which is cast into the housing. They fulfilled my order but stopped shortly - as in a few says - quit filling orders and cancelling them, all the national sources and Cardone themselves. To build one properly, it should be align - bored after the bearings are fitted.

--johnny

Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons. Braselton, Ga. I forgive them all, save those who hurt the dogs. They must answer to me in hell

[Updated on: Mon, 07 October 2019 19:33]

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349046 is a reply to message #348903]

Mon, 07 October 2019 20:51

Scott Nutter

Messages: 782
Registered: January 2015
Location: Houston/San Diego

Karma: 4

Senior Member

Johnny,
According to direct talks with the assistant project manager from GMB, the front shaft bearings on the hi flow and aluminum pumps are roller bearings..
If I knew how to post pictures on this site I would post the email I received from him..
Scott.

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349053 is a reply to message #349046]

Tue, 08 October 2019 00:08

sandy trout

Messages: 51
Registered: October 2018
Location: texas

Karma: 1

Member

So the communication with GMB says the 130-1260P has the rollers in the front and is an aluminum body?
I have a leak up front on the original pump, so Hopefully this will be a good replacement.

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349056 is a reply to message #348903]

Tue, 08 October 2019 07:56

jhbridges

Messages: 8412
Registered: May 2011
Location: Braselton ga

Karma: -74

Senior Member

Scott, I referred to the picture in the url which purports to be that part, and shows ball bearings at the fan end. If the picture isn't that pump, believe the maker. And ask why they used an inaccurate picture Smile

--johnny

Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons. Braselton, Ga. I forgive them all, save those who hurt the dogs. They must answer to me in hell

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349060 is a reply to message #348903]

Tue, 08 October 2019 09:04

Scott Nutter

Messages: 782
Registered: January 2015
Location: Houston/San Diego

Karma: 4

Senior Member

Sandy,
According to GMB, the 130-1260P(cast iron, high flow) and the 130-1260AL(aluminum body, high flow) all have the higher quality roller bearings up front and the higher quality ball bearings in the rear.
They also said that the 130-1260(standard flow, cast iron body) has the STANDARD quality roller bearings up front and the STANDARD quality ball bearings in the rear..
Question is, what do they consider standard quality?
Scott.

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349074 is a reply to message #349060]

Tue, 08 October 2019 14:05

sandy trout

Messages: 51
Registered: October 2018
Location: texas

Karma: 1

Member

Those pictures on Amazon and Ebay don't always represent the item you are buying.
This sounds like the correct pump and as a bonus it is heavy duty.
I see on the Amazon page it also shows what appears to be the same pump last digits 1260P that states aluminum.
The GMB website is lacking in tech info.
Scott, is Meng Ho who you were conversing with on the info?

[Updated on: Tue, 08 October 2019 14:15]

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349079 is a reply to message #348903]

Tue, 08 October 2019 16:20

Scott Nutter

Messages: 782
Registered: January 2015
Location: Houston/San Diego

Karma: 4

Senior Member

Sandy,
Yes, Ming Ho was the person I talked with there . The 1260p is NOT aluminum. The 1260al IS aluminum.
Here is another link...with their cut away.. Scott.
https://www.gmb.net/products/water-pump/

Report message to a moderator

Re: [GMCnet] Cardone water pump AAZ-55-21118H [message #349090 is a reply to message #349079]

Tue, 08 October 2019 20:27

Richard Denney

Messages: 920
Registered: April 2010

Karma: 9

Senior Member

I bought a GMB 1260P and it arrived right before leaving for Mansfield.
Looked aluminum to me, but I didn’t apply the magnet test. I’ll do that
when we get home. It has an 8-blade stamped stainless steel impeller.

I just bought (at a time not of my own choosing) their severe-duty fan
clutch. Made in USA. It’s installed but I haven’t tested it yet.

Rick “whose current pump came with the engine” Denney

On Tue, Oct 8, 2019 at 5:21 PM Scott Nutter via Gmclist <
gmclist@list.gmcnet.org> wrote:

> Sandy,
> Yes, Ming Ho was the person I talked with there . The 1260p is NOT
> aluminum. The 1260al IS aluminum.
> Here is another link...with their cut away.. Scott.
> https://www.gmb.net/products/water-pump/
> --
> Scott Nutter
> 1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final
> drive, Quad bags, tankless water heater, everything Lenzi. Alex Ferrera
> installed MSD Atomic EFI
> Houston, Texas
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
'73 X-Glacier 230 "Jaws"
Northern Virginia
Offlist email: rick at rickdenney dot com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

Re: [GMCnet] Cardone water pump AAZ-55-21118H [message #349093 is a reply to message #349090]

Tue, 08 October 2019 20:43

sandy trout

Messages: 51
Registered: October 2018
Location: texas

Karma: 1

Member

Ming said it should be in the specs for the pump on the bearing type and it probably should be added and he will talk with the engineers to clarify and get back with me tomorrow.
I'm betting it does as the picture you sent shows roller bearings on the pump.

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349094 is a reply to message #348903]

Tue, 08 October 2019 20:54

Scott Nutter

Messages: 782
Registered: January 2015
Location: Houston/San Diego

Karma: 4

Senior Member

Rick.
Now that's confusing with the fan clutch... GMB doesn't list any manufacturing in the USA... maybe it's a Hayden branded as a GMB???
The more I look into this stuff, the more smoke and mirrors I find.....
Now I know the stress Jim K must feel while trying to source parts for the GMC community... maybe just another reason to let the suppliers handle it..
Scott.

Report message to a moderator

Re: [GMCnet] Cardone water pump AAZ-55-21118H [message #349103 is a reply to message #349094]

Wed, 09 October 2019 08:07

Richard Denney

Messages: 920
Registered: April 2010

Karma: 9

Senior Member

Scott, you still have to check stuff from the suppliers—they can’t check
every detail and we can be a picky crowd with conflicting expectations and
requirements.

The Amazon listing I used for the clutch looks like what I got, but it
looks different than pictures I see of a Hayden 2797 or 2784. It’s very
similar to a Delco 4644. Shipping originated from an Amazon warehouse (?)
in Etna, Ohio. I’m driving back to Virginia using it, so we’ll see.

Rick “magnet test on the water pump forthcoming” Denney

On Tue, Oct 8, 2019 at 9:55 PM Scott Nutter via Gmclist <
gmclist@list.gmcnet.org> wrote:

> Rick.
> Now that's confusing with the fan clutch... GMB doesn't list any
> manufacturing in the USA... maybe it's a Hayden branded as a GMB???
> The more I look into this stuff, the more smoke and mirrors I find.....
> Now I know the stress Jim K must feel while trying to source parts for
> the GMC community... maybe just another reason to let the suppliers handle
> it..
>
> --
'73 X-Glacier 230 "Jaws"
Northern Virginia
Offlist email: rick at rickdenney dot com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349118 is a reply to message #348903]

Wed, 09 October 2019 15:05

sandy trout

Messages: 51
Registered: October 2018
Location: texas

Karma: 1

Member

Here is what I got back from Meng Ho, Assistant manager/Product Management at GMB Ph# 6096552422 ext 131

We got the reply from our factory and the design of the bearing shaft is ball/ball bearing.
However as 130-1260P is made in JP using GMB made bearings, we believe the quality is good for the application.

I had explained to him in a previous email as to the application on the GMC motorhome with the 403/455 engine and the heavy thrust load on the bearings.
With the Cardone pump gone, I will give this one a shot.

Report message to a moderator

Re: Cardone water pump AAZ-55-21118H [message #349152 is a reply to message #349118]

Thu, 10 October 2019 20:33

sandy trout

Messages: 51
Registered: October 2018
Location: texas

Karma: 1

Member

Thanks for the pump number, Scott, ordered it from Amazon.

Report message to a moderator

Re: [GMCnet] Cardone water pump AAZ-55-21118H [message #349381 is a reply to message #349090]

Thu, 17 October 2019 12:51

Dave Stragand

Messages: 307
Registered: October 2017

Karma: 0

Senior Member

The GMB 130-1260P I received is indeed aluminum. It weighs 5.15 pounds. The front shaft has the markings "C19165-35A L GMB" on it. No idea if that translates to a roller bearing, though. Very nice looking pump, however.

1978 Transmode (403) Pittsburgh, PA

Report message to a moderator

Pages (2): [1 2 › »]

Previous Topic:	Long time GMCer Mike Beaton
Next Topic:	Fuel starvation cure for me...

Goto Forum:

-=] Back to Top [=-

Current Time: Fri Sep 06 11:10:09 CDT 2024

Total time taken to generate the page: 0.01326 seconds