GMCforum: GMCnet » ONAN starting

Home » Public Forums » GMCnet » ONAN starting (starter stays engaged after starting)

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] ONAN starting [message #320846 is a reply to message #320841]

Sat, 22 July 2017 14:07

William Shourt

Messages: 35
Registered: August 2015

Karma:

Member

Terry the 8 volts is on the wire from K1 to starter solenoid when engine is running. The 8 volts drops to 0 when wire is pulled from solenoid and starter disengages. Measured on wire to solenoid.

Sent from my iPad

> On Jul 22, 2017, at 11:29 AM, Terry wrote:
>
> As Ken posted, there should be 12 volts (battery voltage) on the K1 terminal, not 8. This is a common positive relay and the relay action is activated
> by a switched ground. What happens when you remove the grounding wire? Why is there only 8 volts on the power feed? Measure the resistance to ground
> on that ground trigger wire after it starts and then you remove it. If removing it does not stop the starter, then there is a ground leak right there
> at the relay. If the starter stops, check that wire and circuit for a ground leak with your multimeter or test light. If you have 8 volts on THAT
> wire, then it must be the difference between 8 and 12 that is keeping the relay triggered.
> --
> Terry Kelpien
>
> ASE Master Technician
>
> 73 Glacier 260
>
> Smithfield, Va.
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

[Message index]

		ONAN starting By: Bill Shourt on Fri, 21 July 2017 14:04
		Re: [GMCnet] ONAN starting By: James Hupy on Fri, 21 July 2017 14:49
		Re: [GMCnet] ONAN starting By: William Shourt on Fri, 21 July 2017 18:15
		Re: [GMCnet] ONAN starting By: Carl S. on Fri, 21 July 2017 19:09
		Re: [GMCnet] ONAN starting By: William Shourt on Fri, 21 July 2017 19:17
		Re: ONAN starting By: lqqkatjon on Fri, 21 July 2017 22:35
		Re: ONAN starting By: Ken Burton on Sat, 22 July 2017 04:11
		Re: [GMCnet] ONAN starting By: Mr ERFisher on Sat, 22 July 2017 04:49
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 07:51
		Re: [GMCnet] ONAN starting By: Ken Burton on Sat, 22 July 2017 10:54
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 13:29
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 14:07
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 14:48
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 13:46
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sat, 22 July 2017 18:00
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 19:09
		Re: [GMCnet] ONAN starting By: bwevers on Sat, 22 July 2017 20:32
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sat, 22 July 2017 22:51
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sun, 23 July 2017 09:53
		Re: [GMCnet] ONAN starting By: William Shourt on Sun, 23 July 2017 18:17
		Re: [GMCnet] ONAN starting By: Guy Lopes on Tue, 25 July 2017 00:51
		Re: [GMCnet] ONAN starting By: Bruce Hart on Tue, 25 July 2017 05:59
		Re: [GMCnet] ONAN starting By: Ken Henderson on Tue, 25 July 2017 06:09
		Re: [GMCnet] ONAN starting By: jimk on Tue, 25 July 2017 10:03
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:23
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:29
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:32
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 14:19
		Re: [GMCnet] ONAN starting By: Ken Burton on Tue, 25 July 2017 15:11
		Re: [GMCnet] ONAN starting By: Emery Stora on Tue, 25 July 2017 20:30
		Re: [GMCnet] ONAN starting By: Ken Henderson on Tue, 25 July 2017 21:15
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 07:57
		Re: ONAN starting By: lqqkatjon on Sat, 22 July 2017 15:32
		Re: ONAN starting By: Ken Burton on Sat, 22 July 2017 20:14
		Re: ONAN starting By: JohnL455 on Sun, 23 July 2017 16:34
		Re: ONAN starting By: JohnL455 on Sun, 23 July 2017 16:38
		Re: ONAN starting By: Ken Burton on Sun, 23 July 2017 21:17
		Re: [GMCnet] ONAN starting By: William Shourt on Sun, 23 July 2017 23:09
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sun, 23 July 2017 23:35
		Re: ONAN starting about 2 K windings By: Matt Colie on Mon, 24 July 2017 09:28
		Re: [GMCnet] ONAN starting about 2 K windings By: William Shourt on Mon, 24 July 2017 13:26
		Re: [GMCnet] ONAN starting about 2 K windings By: Ken Henderson on Mon, 24 July 2017 20:56
		Re: [GMCnet] ONAN starting about 2 K windings By: Bullitthead on Mon, 24 July 2017 23:15
		Re: [GMCnet] ONAN starting about 2 K windings By: William Shourt on Mon, 24 July 2017 23:23
		Re: ONAN starting about 2 K windings By: Ken Burton on Mon, 24 July 2017 23:19
		Re: ONAN starting about 2 K windings By: Ken Burton on Tue, 25 July 2017 01:15
		Re: [GMCnet] ONAN starting about 2 K windings By: Ken Henderson on Tue, 25 July 2017 06:14
		Re: ONAN starting By: bwevers on Tue, 25 July 2017 00:22

Previous Topic:	Tank sending units
Next Topic:	403 passenger side exhaust manifold needed in midwest

Goto Forum:

-=] Back to Top [=-

Current Time: Thu Oct 31 20:04:56 CDT 2024

Total time taken to generate the page: 0.01776 seconds