GMCforum: GMCnet » [GMCnet] block off plates

Home » Public Forums » GMCnet » [GMCnet] block off plates

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] block off plates [message #208889 is a reply to message #208855]

Sun, 26 May 2013 20:40

USAussie

Messages: 15912
Registered: July 2007
Location: Sydney, Australia

Karma:

Senior Member

Fred,

Thanks.

I re-read the procedure and wanted to add something. I am concerned with putting too much force on the carb mounting bolt threads /
manifold / engine / GMC floor. I'm not sure if the following would work but it might be worth a shot to see if and when the engine
moves upwards.

Take a small bubble level and sit it on the carb mounting face. Watch it as you tighten the all thread nuts; I believe as you raise
the engine the bubble should move and as soon as it does stop tightening the nuts. If you have a smart phone they have free apps for
this, I run one called Bubble Level from BRL Technologies on my Samsung.

Regards,
Rob

-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org [mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Kathy and Fred Estabrook
Sent: Sunday, May 26, 2013 1:04 PM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] block off plates

Thanks Chuck Howard and Matt and a special thanks to you Rob. This will be
my project next week and I will let you know how I'm doing.
Fred

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426

Report message to a moderator

[Message index]

		[GMCnet] block off plates By: Kathy and Fred Estabr on Sat, 25 May 2013 11:41
		Re: [GMCnet] block off plates By: C Boyd on Sat, 25 May 2013 12:09
		Re: [GMCnet] block off plates By: hnielsen2 on Sat, 25 May 2013 14:16
		Re: [GMCnet] block off plates By: Matt Colie on Sat, 25 May 2013 15:51
		Re: [GMCnet] block off plates By: USAussie on Sat, 25 May 2013 20:29
		Re: [GMCnet] block off plates By: WD0AFQ on Sat, 25 May 2013 21:36
		Re: [GMCnet] block off plates By: Kathy and Fred Estabr on Sat, 25 May 2013 22:37
		Re: [GMCnet] block off plates By: USAussie on Sun, 26 May 2013 10:02
		Re: [GMCnet] block off plates By: Kathy and Fred Estabr on Sun, 26 May 2013 13:03
		Re: [GMCnet] block off plates By: USAussie on Sun, 26 May 2013 20:40
		Re: [GMCnet] block off plates By: Kathy and Fred Estabr on Thu, 30 May 2013 10:59

Previous Topic:	[GMCnet] Tire Advice ~ Load Range
Next Topic:	[GMCnet] EZ Cool Firewall Insulation

Goto Forum:

-=] Back to Top [=-

Current Time: Sun Nov 10 13:49:17 CST 2024

Total time taken to generate the page: 0.00849 seconds