Home » Public Forums » GMCnet » Yandina combiner cycles
Re: Yandina combiner cycles [message #329967 is a reply to message #328332] |
Wed, 14 March 2018 09:16 ![Go to previous message Go to previous message](/GMCforum/theme/default/images/up.png) ![Go to next message Go to previous message](/GMCforum/theme/default/images/down.png) |
Tilerpep
![United States United States](/GMCforum/images/flags/us.png) Messages: 404 Registered: June 2013 Location: Raleigh, NC
Karma:
|
Senior Member |
|
|
Update
More info, and a few experiments:
The 78 had a West Marine 150 combiner, which has a little label hidden on the back that said it was a Yandina and it needed the "minimum six feet of 6 gauge or less wire" connecting it (which it did not have). The Yandina site says this particular model is discontinued. I bought six feet of 8 gauge wire, split it to three foot sections and moved the Yandina/West Marine unit to the 75, keeping the isolator. Wow, 8 gauge was overkill, and too stiff to work with easily. I forget (have read on here before) why the six feet is needed.
I installed the new victron combiner in the 78 (no isolator). It did not say anything about six feet of lead wire, so I used the previous connectors.
Yesterday I worked in the 78 with all the interior lights and running lights on to load both systems while I fiddled with a new rotor, cap, timing and bunch of other systems. It did cycle the combiner, but not too often, and the noise is less of a clunk. With only the house side loaded, it seemed to cycle less than the Yandina.
I paid about $50 for the Victron, and Jim K has the Yandina 100 for $65 with the wiring premade. The Victron does not have an indicator light telling you when it is combining, the Yandina does. I think I would go with Jim K's Yandina if I were doing another one, both are a nice addition to stock setup.
1975 Glenbrook, 1978 Royale rear bath
Raleigh, NC
|
|
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Yandina combiner cycles
By: Tilerpep on Wed, 17 January 2018 09:01
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
By: Tomtom on Wed, 17 January 2018 10:38
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
By: Tilerpep on Wed, 17 January 2018 11:18
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
By: Tilerpep on Wed, 17 January 2018 12:31
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
By: Tilerpep on Wed, 17 January 2018 12:55
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: [GMCnet] Yandina combiner cycles
By: bdub on Wed, 17 January 2018 15:10
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: [GMCnet] Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
By: RF_Burns on Wed, 17 January 2018 20:42
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
By: midlf on Wed, 17 January 2018 20:37
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
By: JohnL455 on Fri, 19 January 2018 11:00
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
By: Tilerpep on Wed, 14 March 2018 09:16
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: [GMCnet] Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: [GMCnet] Yandina combiner cycles
|
![Read Message Read Message](/GMCforum/theme/default/images/read.png) |
|
Re: [GMCnet] Yandina combiner cycles
|
Goto Forum:
Current Time: Fri Jun 14 20:42:08 CDT 2024
Total time taken to generate the page: 0.01297 seconds
|