GMCforum: GMCnet » ONAN starting

Home » Public Forums » GMCnet » ONAN starting (starter stays engaged after starting)

Show: Today's Messages :: Polls :: Message Navigator

Re: ONAN starting [message #320857 is a reply to message #320850]

Sat, 22 July 2017 20:14

Ken Burton

Messages: 10030
Registered: January 2004
Location: Hebron, Indiana

Karma:

Senior Member

First, Please use Colonel Ken's wiring diagram. It is a lot easier to read and it gives us a common diagram to talk about.

I was misunderstood where you were taking voltage readings. Just to make sure, I now think you are taking voltage reading at the N/O point on K1 that goes to the starter and choke. You are not reading the K1 coil leads going to +12 and the K1 coil lead going to Onan board pin 7.

If the above is true, then I need to rethink the problem again.

Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana

Report message to a moderator

[Message index]

		ONAN starting By: Bill Shourt on Fri, 21 July 2017 14:04
		Re: [GMCnet] ONAN starting By: James Hupy on Fri, 21 July 2017 14:49
		Re: [GMCnet] ONAN starting By: William Shourt on Fri, 21 July 2017 18:15
		Re: [GMCnet] ONAN starting By: Carl S. on Fri, 21 July 2017 19:09
		Re: [GMCnet] ONAN starting By: William Shourt on Fri, 21 July 2017 19:17
		Re: ONAN starting By: lqqkatjon on Fri, 21 July 2017 22:35
		Re: ONAN starting By: Ken Burton on Sat, 22 July 2017 04:11
		Re: [GMCnet] ONAN starting By: Mr ERFisher on Sat, 22 July 2017 04:49
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 07:51
		Re: [GMCnet] ONAN starting By: Ken Burton on Sat, 22 July 2017 10:54
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 13:29
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 14:07
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 14:48
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 13:46
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sat, 22 July 2017 18:00
		Re: [GMCnet] ONAN starting By: Bullitthead on Sat, 22 July 2017 19:09
		Re: [GMCnet] ONAN starting By: bwevers on Sat, 22 July 2017 20:32
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sat, 22 July 2017 22:51
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sun, 23 July 2017 09:53
		Re: [GMCnet] ONAN starting By: William Shourt on Sun, 23 July 2017 18:17
		Re: [GMCnet] ONAN starting By: Guy Lopes on Tue, 25 July 2017 00:51
		Re: [GMCnet] ONAN starting By: Bruce Hart on Tue, 25 July 2017 05:59
		Re: [GMCnet] ONAN starting By: Ken Henderson on Tue, 25 July 2017 06:09
		Re: [GMCnet] ONAN starting By: jimk on Tue, 25 July 2017 10:03
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:23
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:29
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 13:32
		Re: [GMCnet] ONAN starting By: William Shourt on Tue, 25 July 2017 14:19
		Re: [GMCnet] ONAN starting By: Ken Burton on Tue, 25 July 2017 15:11
		Re: [GMCnet] ONAN starting By: Emery Stora on Tue, 25 July 2017 20:30
		Re: [GMCnet] ONAN starting By: Ken Henderson on Tue, 25 July 2017 21:15
		Re: [GMCnet] ONAN starting By: William Shourt on Sat, 22 July 2017 07:57
		Re: ONAN starting By: lqqkatjon on Sat, 22 July 2017 15:32
		Re: ONAN starting By: Ken Burton on Sat, 22 July 2017 20:14
		Re: ONAN starting By: JohnL455 on Sun, 23 July 2017 16:34
		Re: ONAN starting By: JohnL455 on Sun, 23 July 2017 16:38
		Re: ONAN starting By: Ken Burton on Sun, 23 July 2017 21:17
		Re: [GMCnet] ONAN starting By: William Shourt on Sun, 23 July 2017 23:09
		Re: [GMCnet] ONAN starting By: Ken Henderson on Sun, 23 July 2017 23:35
		Re: ONAN starting about 2 K windings By: Matt Colie on Mon, 24 July 2017 09:28
		Re: [GMCnet] ONAN starting about 2 K windings By: William Shourt on Mon, 24 July 2017 13:26
		Re: [GMCnet] ONAN starting about 2 K windings By: Ken Henderson on Mon, 24 July 2017 20:56
		Re: [GMCnet] ONAN starting about 2 K windings By: Bullitthead on Mon, 24 July 2017 23:15
		Re: [GMCnet] ONAN starting about 2 K windings By: William Shourt on Mon, 24 July 2017 23:23
		Re: ONAN starting about 2 K windings By: Ken Burton on Mon, 24 July 2017 23:19
		Re: ONAN starting about 2 K windings By: Ken Burton on Tue, 25 July 2017 01:15
		Re: [GMCnet] ONAN starting about 2 K windings By: Ken Henderson on Tue, 25 July 2017 06:14
		Re: ONAN starting By: bwevers on Tue, 25 July 2017 00:22

Previous Topic:	Tank sending units
Next Topic:	403 passenger side exhaust manifold needed in midwest

Goto Forum:

-=] Back to Top [=-

Current Time: Thu Oct 31 19:13:00 CDT 2024

Total time taken to generate the page: 0.02431 seconds